fxtv und sound

hallo liste!

hat einer von euch fxtv mit sound zum laufen gebracht? das programm
funktioniert bei mir recht gut, bis auf die tatsache, daß kein sound
kommt. ich habe den sound anhand von mp3 und musikcds getestet und da
gibts keinerlei probleme. daran kanns also nicht liegen. ich habe eine
haupage winTV.

ich habe eine soundblaster awe64 isa/pnp noch ein uralt modell. der
treiber von opensound erkennt sie als type-1. ich verwende den newpcm
treiber, der allerdings den nachteil hat, daß er den emu8000 chip auf
meiner karte nicht unterstützt, was der alte voxwaretreiber aber
geschafft hat. nur den kann ich nicht mehr hernehmen, weil das prog
pnp mit dem ich in meiner kernel.conf die einstellungen gemacht habe
unter 4.0-stable nicht existiert. ist sehr schade, weil 8MB speicher
draufstecken.

übrigens gings unter 3.4 ohne kabel vom lineout der tv-karte zum
linein von meiner soundkarte. keine ahnung warum.

hier meine kernelconfig und der output von dmesg:

# Audio drivers: `snd', `sb', `pas', `gus', `pca'
#
# snd: Voxware sound support code
# sb: SoundBlaster PCM - SoundBlaster, SB Pro, SB16, ProAudioSpectrum
# sbxvi: SoundBlaster 16
# sbmidi: SoundBlaster 16 MIDI interface
# pas: ProAudioSpectrum PCM and MIDI
# gus: Gravis Ultrasound - Ultrasound, Ultrasound 16, Ultrasound MAX
# gusxvi: Gravis Ultrasound 16-bit PCM (do not use)
# mss: Microsoft Sound System
# css: Crystal Sound System (CSS 423x PnP)
# sscape: Ensoniq Soundscape MIDI interface
# sscape_mss: Ensoniq Soundscape PCM (requires sscape)
# opl: Yamaha OPL-2 and OPL-3 FM - SB, SB Pro, SB 16, ProAudioSpectrum
# uart: stand-alone 6850 UART for MIDI
# mpu: Roland MPU-401 stand-alone card
#
# Note: It has been reported that ISA DMA with the SoundBlaster will
# lock up the machine (PR docs/5358). If this happens to you,
# turning off USWC write posting in your machine's BIOS may fix
# the problem.
#
# Beware! The addresses specified below are also hard-coded in
# src/sys/i386/isa/sound/sound_config.h. If you change the values here, you
# must also change the values in the include file.
#
# pcm: PCM audio through various sound cards.
#
# This has support for a large number of new audio cards, based on
# CS423x, OPTi931, Yamaha OPL-SAx, and also for SB16, GusPnP.
# For more information about this driver and supported cards,
# see the pcm.4 man page.
#
# The flags of the device tells the device a bit more info about the
# device that normally is obtained through the PnP interface.
# bit 2..0 secondary DMA channel;
# bit 4 set if the board uses two dma channels;
# bit 15..8 board type, overrides autodetection; leave it
# zero if don't know what to put in (and you don't,
# since this is unsupported at the moment...).
#
# This driver will use the new PnP code if it's available.
#
# pca: PCM audio through your PC speaker
#
# If you have a GUS-MAX card and want to use the CS4231 codec on the
# card the drqs for the gus max must be 8 bit (1, 2, or 3).
#
# If you would like to use the full duplex option on the gus, then define
# flags to be the ``read dma channel''.
#
# options BROKEN_BUS_CLOCK #PAS-16 isn't working and OPTI chipset
# options SYMPHONY_PAS #PAS-16 isn't working and SYMPHONY chipset
# options EXCLUDE_SBPRO #PAS-16
# options SBC_IRQ=5 #PAS-16. Must match irq on sb0 line.
# PAS16: The order of the pas0/sb0/opl0 is important since the
# sb emulation is enabled in the pas-16 attach.
#
# To override the GUS defaults use:
# options GUS_DMA2
# options GUS_DMA
# options GUS_IRQ
#
# The src/sys/i386/isa/sound/sound.doc has more information.

# Controls all "VOXWARE" driver sound devices. See Luigi's driver
# below for an alternate which may work better for some cards.
#
#device snd
#device pas0 at isa? port 0x388 irq 10 drq 6
#device sb0 at isa? port 0x220 irq 5 drq 1
#device sbxvi0 at isa? drq 5
#device sbmidi0 at isa? port 0x330
#device awe0 at isa? port 0x620
#device gus0 at isa? port 0x220 irq 12 drq 1
##device gus0 at isa? port 0x220 irq 12 drq 1 flags 0x3
#device mss0 at isa? port 0x530 irq 10 drq 1
#device css0 at isa? port 0x534 irq 5 drq 1 flags 0x08
#device sscape0 at isa? port 0x330 irq 9 drq 0
#device trix0 at isa? port 0x330 irq 6 drq 0
#device sscape_mss0 at isa? port 0x534 irq 5 drq 1
#device opl0 at isa? port 0x388
#device mpu0 at isa? port 0x330 irq 6 drq 0
#device uart0 at isa? port 0x330 irq 5

# The newpcm driver (use INSTEAD of snd0 and all VOXWARE drivers!).
# Note that motherboard sound devices may require options PNPBIOS.
#
# Supported cards include:
# Creative SoundBlaster ISA PnP/non-PnP
# Supports ESS and Avance ISA chips as well.
# Gravis UltraSound ISA PnP/non-PnP
# Crystal Semiconductor CS461x/428x PCI
# Neomagic 256AV (ac97)
# Most of the more common ISA/PnP sb/mss/ess compatable cards.

# For non-pnp sound cards with no bridge drivers only:
#device pcm0 at isa? irq 10 drq 1 flags 0x0
#
# For PnP/PCI sound cards
device pcm

# The bridge drivers for sound cards. These can be seperately configured
# for providing services to the likes of new-midi (not in the tree yet).
# When used with 'device pcm' they also provide pcm sound services.
#
# sbc: Creative SoundBlaster ISA PnP/non-PnP
# Supports ESS and Avance ISA chips as well.
# gusc: Gravis UltraSound ISA PnP/non-PnP
# csa: Crystal Semiconductor CS461x/428x PCI

# For non-PnP cards:
#device sbc0 at isa? port 0x220 irq 5 drq 1 flags 0x15
#device gusc0 at isa? port 0x220 irq 5 drq 1 flags 0x13
device sbc
#device joy0 at isa? port IO_GAME

# Not controlled by `snd'
#device pca0 at isa? port IO_TIMER1

# The 'bktr' device is a PCI video capture device using the Brooktree
# bt848/bt848a/bt849a/bt878/bt879 chipset. When used with a TV Tuner it forms a
# TV card, eg Miro PC/TV, Hauppauge WinCast/TV WinTV, VideoLogic Captivator,
# Intel Smart Video III, AverMedia, IMS Turbo, FlyVideo.
#
# options OVERRIDE_CARD=xxx
# options OVERRIDE_TUNER=xxx
# options OVERRIDE_MSP=1
# options OVERRIDE_DBX=1
# These options can be used to override the auto detection
# The current values for xxx are found in src/sys/dev/bktr/bktr_card.h
# Using sysctl(8) run-time overrides on a per-card basis can be made
#
# options BROOKTREE_SYSTEM_DEFAULT=BROOKTREE_PAL
# or
# options BROOKTREE_SYSTEM_DEFAULT=BROOKTREE_NTSC
# Specifes the default video capture mode.
# This is required for Dual Crystal (28&35Mhz) boards where PAL is used
# to prevent hangs during initialisation. eg VideoLogic Captivator PCI.
#
options BKTR_USE_PLL
# PAL or SECAM users who have a 28Mhz crystal (and no 35Mhz crystal)
# must enable PLL mode with this option. eg some new Bt878 cards.
#
# options BKTR_GPIO_ACCESS
# This enable IOCTLs which give user level access to the GPIO port.
#
# options BKTR_NO_MSP_RESET
# Prevents the MSP34xx reset. Good if you initialise the MSP in another OS first
#
# options BKTR_430_FX_MODE
# Switch Bt878/879 cards into Intel 430FX chipset compatibility mode.
#
# options BKTR_SIS_VIA_MODE
# Switch Bt878/879 cards into SIS/VIA chipset compatibility mode which is
# needed for some old SiS and VIA chipset motherboards.
# This also allows Bt878/879 chips to work on old OPTi (<1997) chipset
# motherboards and motherboards with bad or incomplete PCI 2.1 support.
# As a rough guess, old = before 1998
#
#
# Brooktree driver has been ported to the new I2C framework. Thus,
# you'll need to have the following 3 lines in the kernel config.
# device smbus
# device iicbus
# device iicbb
# The iic and smb devices are only needed if you want to control other
# I2C slaves connected to the external connector of some cards.
#
device bktr

# SMB bus
#
# System Management Bus support provided by the 'smbus' device.
#
# Supported devices:
# smb standard io
#
# Supported interfaces:
# iicsmb I2C to SMB bridge with any iicbus interface
# bktr brooktree848 I2C hardware interface
# intpm Intel PIIX4 Power Management Unit
# alpm Acer Aladdin-IV/V/Pro2 Power Management Unit
#
device smbus # Bus support, required for smb below.
device intpm
#device alpm

device smb

#
# I2C Bus
#
# Philips i2c bus support is provided by the `iicbus' device.
#
# Supported devices:
# ic i2c network interface
# iic i2c standard io
# iicsmb i2c to smb bridge. Allow i2c i/o with smb commands.
#
# Supported interfaces:
# pcf Philips PCF8584 ISA-bus controller
# bktr brooktree848 I2C software interface
#
# Other:
# iicbb generic I2C bit-banging code (needed by lpbb, bktr)
#
device iicbus # Bus support, required for ic/iic/iicsmb below.
device iicbb

#device ic
device iic
device iicsmb # smb over i2c bridge

#device pcf0 at isa? port 0x320 irq 5

Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1982, 1986, 1989, 1991, 1993
        The Regents of the University of California. All rights reserved.
FreeBSD 4.0-STABLE #0: Thu Jun 22 05:13:20 CEST 2000
    root(at)hal.matof.de:/usr/src/sys/compile/HAL
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (300.68-MHz 686-class CPU)
  Origin = "GenuineIntel" Id = 0x634 Stepping = 4
  Features=0x80f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,MMX>
real memory = 67096576 (65524K bytes)
config> quit
avail memory = 61935616 (60484K bytes)
Preloaded elf kernel "kernel" at 0xc0322000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc032209c.
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
apm0: <APM BIOS> on motherboard
apm: found APM BIOS v1.2, connected at v1.2
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <ATI Mach64-GB graphics accelerator> at 0.0 irq 9
isab0: <Intel 82371AB PCI to ISA bridge> at device 4.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xb800-0xb80f at device 4.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <Intel 82371AB/EB (PIIX4) USB controller> at 4.2
intpm0: <Intel 82371AB Power management controller> port 0xe800-0xe80f irq 9 at device 4.3 on pci0
intpm0: I/O mapped e800
intpm0: intr IRQ 9 enabled revision 0
smbus0: <System Management Bus> on intsmb0
smb0: <SMBus general purpose I/O> on smbus0
intpm0: PM I/O mapped e400
bktr0: <BrookTree 878> mem 0xe2000000-0xe2000fff irq 9 at device 9.0 on pci0
iicbb0: <I2C generic bit-banging driver> on bti2c0
iicbus0: <Philips I2C bus> on iicbb0 master-only
iicsmb0: <I2C to SMB bridge> on iicbus0
smbus1: <System Management Bus> on iicsmb0
smb1: <SMBus general purpose I/O> on smbus1
iic0: <I2C general purpose I/O> on iicbus0
smbus2: <System Management Bus> on bti2c0
smb2: <SMBus general purpose I/O> on smbus2
bktr0: Hauppauge Model 61324 D208
bktr0: Detected a MSP3415D-A2 at 0x80
Hauppauge WinCast/TV, Philips PAL I tuner, msp3400c stereo, remote control.
pci0: <unknown card> (vendor=0x109e, dev=0x0878) at 9.1 irq 9
ed0: <NE2000 PCI Ethernet (RealTek 8029)> port 0xb000-0xb01f irq 9 at device 10.0 on pci0
ed0: address 00:00:1c:01:14:c3, type NE2000 (16 bit)
pci0: <3Dfx Voodoo 2 graphics accelerator> at 12.0
isa0: too many dependant configs (8)
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
ppi0: <Parallel I/O> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
sbc0: <Creative SB AWE64> at port 0x220-0x22f,0x330-0x331,0x388-0x38b irq 5 drq 1,5 on isa0
sbc0: setting card to irq 5, drq 1, 5
pcm0: <SB DSP 4.16> on sbc0
unknown0: <Game> at port 0x200-0x207 on isa0
unknown1: <WaveTable> at port 0x620-0x623 on isa0
unknown2: <Generic ESDI/IDE/ATA controller> at port 0x168-0x16f,0x36e-0x36f irq 10 on isa0
ad0: 8063MB <IBM-DHEA-38451> [16383/16/63] at ata0-master using UDMA33
acd0: CDROM <LTN382> at ata0-slave using PIO4
acd1: CD-R <CR-4801TE> at ata1-master using PIO3
Mounting root from ufs:/dev/ad0s2a

-- 
Viele Grüße
	Oliver Helmling
To Unsubscribe: send mail to majordomo(at)de.FreeBSD.org
with "unsubscribe de-bsd-questions" in the body of the message