Re: Proxim Harmony PCI Installationsprobleme

Hallo,

für das Archiv hier die Lösung...

Es fehlte der Eintrag:

# Proxim Harmony PCI Card 802.11b NIC
card "PROXIM" "LAN PCI CARD HARMONY 80211B"
        config auto "wi" ?
        insert /etc/pccard_ether $device start
        remove /etc/pccard_ether $device stop

in der /etc/pccard.conf

Leider hab ich es noch nicht geschafft ein Laptop mit der Karte
zu verbinden.
Hab mich an das Handbuch gehalten aber pingen konnte ich noch
nichts.
Auffällig war das mein Laptop 200 gesendete Pakete angab aber 0
empfangene obwohl die Verbindung bestanden hat.

On Mon, Dec 08, 2003 at 10:42:59PM +0100, Oliver Velten wrote:
> Hallo,
>
> ich habe mir eine Proxim Harmony 802.11b PCI Karte gekauft und
> versuche sie unter FreeBSD zum laufen zu bekommen.
> Das Problem ist dass ifconfig -a kein wi Device anzeigt. Ich hab
> aber in der Kernelkonfiguration device wi mit einkompiliert.
>
> Hat die schon jemand am laufen?
>
> Jetzt kommen ein paar Ausgaben von diversen Programmen:
>
> scanpci sagt:
> pci bus 0x0000 cardnum 0x0b function 0x00: vendor 0x1013 device
> 0x1100
> Cirrus Logic CL 6729
>
> Das ist wohl der pcmcia Adapter.
>
> Und hier noch etwas längeres
>
>
> root(at)zeus:~> pccardc dumpcis
> Configuration data for card in slot 0
> Tuple #1, code = 0x1 (Common memory descriptor), length = 3
> 000: 00 00 ff
> Common memory device information:
> Device number 1, type No device, WPS = OFF
> Speed = No speed, Memory block size = 512b, 1
> units
> Tuple #2, code = 0x17 (Attribute memory descriptor), length = 4
> 000: 67 5a 08 ff
> Attribute memory device information:
> Device number 1, type SRAM, WPS = OFF
> Speed = 5.0 x 100 ns, Memory block size = 512b, 2
> units
> Tuple #3, code = 0x1d (Other conditions for attribute memory),
> length = 5
> 000: 03 67 5a 08 ff
> (MWAIT) (3V card)
> Tuple #4, code = 0x15 (Version 1 info), length = 80
> 000: 05 00 50 52 4f 58 49 4d 00 4c 41 4e 20 50 43 49
> 010: 20 43 41 52 44 20 48 41 52 4d 4f 4e 59 20 38 30
> 020: 32 31 31 42 00 00 00 00 00 00 00 00 00 00 00 00
> 030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 040: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ff
> Version = 5.0, Manuf = [PROXIM], card vers = [LAN PCI
> CARD HARMONY 80211
> B]
> Addit. info = [],[]
> Tuple #5, code = 0x20 (Manufacturer ID), length = 4
> 000: 26 01 02 00
> PCMCIA ID = 0x126, OEM ID = 0x2
> Tuple #6, code = 0x21 (Functional ID), length = 2
> 000: 06 00
> Network/LAN adapter
> Tuple #7, code = 0x22 (Functional EXT), length = 2
> 000: 01 07
> Network technology: Wireless
> Tuple #8, code = 0x22 (Functional EXT), length = 5
> 000: 02 40 42 0f 00
> Network speed: 1 Mb/sec
> Tuple #9, code = 0x22 (Functional EXT), length = 5
> 000: 02 80 84 1e 00
> Network speed: 2 Mb/sec
> Tuple #10, code = 0x22 (Functional EXT), length = 5
> 000: 02 60 ec 53 00
> Network speed: 5 Mb/sec
> Tuple #11, code = 0x22 (Functional EXT), length = 5
> 000: 02 c0 d8 a7 00
> Network speed: 11 Mb/sec
> Tuple #12, code = 0x22 (Functional EXT), length = 2
> 000: 03 07
> Network media: 2.4 GHz
> Tuple #13, code = 0x22 (Functional EXT), length = 8
> 000: 04 06 00 00 f0 64 00 00
> Network node ID: 00 00 f0 64 00 00
> Tuple #14, code = 0x22 (Functional EXT), length = 2
> 000: 05 01
> Network connector: closed connector standard
> Tuple #15, code = 0x1a (Configuration map), length = 7
> 000: 03 01 e0 03 00 00 01
> Reg len = 4, config register addr = 0x3e0, last config =
> 0x1
> Registers: X-------
> Tuple #16, code = 0x1b (Configuration entry), length = 13
> 000: c1 01 09 77 b5 1e 35 b5 3c 36 36 05 46
> Config index = 0x1(default)
> Interface byte = 0x1 (I/O)
> Vcc pwr:
> Nominal operating supply voltage: 3 x 1V, ext =
> 0x1e
> Minimum operating supply voltage: 3 x 1V
> Maximum operating supply voltage: 3 x 1V, ext =
> 0x3c
> Max current average over 1 second: 3 x 100mA
> Max current average over 10 ms: 3 x 100mA
> Power down supply current: 1 x 10mA
> Card decodes 6 address lines, limited 8/16 Bit I/O
> Tuple #17, code = 0xff (Terminator), length = 0
> 2 slots found
>
>

Cheers,
                Oliver

-- 
http://www.baily.de/
To Unsubscribe: send mail to majordomo.FreeBSD.org
with "unsubscribe de-bsd-questions" in the body of the message