installation fritz!classic auf 4.2

Hi,

ich fürchte, ich sehe den Wald vor lauter Bäumen nicht. Mal abgesehen davon,
dass Interrupts auf Intel-Hardware nicht meine Welt sind...

Also, fritz!classic in einem frisch aufgesetzten 4.2.
conf:
options AVM_A1
device isic0 at isa? port 0x300 irq 15 flags 4

Und dann beim Booten:
isic0: Could not get an irq for AVM A1/Fritz!

Die Definition aus der Manpage
(isic0 at isa? port 0x300 irq 15 flags 4 vector isicintr) geht gar nicht
durch's /usr/sbin/config , die oben ist aus LINT.
Das einzige, was nicht SCSI im Rechner ist ist die Floppy.

Blöderweise läuft die Karte mit diesem port/irq auf dem Fensterl95 auf der
anderen Platte einwandfrei. PnP ist abgeschaltet im Bios.

Die Ausgabe von dmsg hängt unten dran.

Hat jemand den entscheidenen Tip ?

Gruß und Dank
                Axel

Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
 The Regents of the University of California. All rights reserved.
FreeBSD 4.2-RELEASE #10: Mon Dec 4 22:29:28 CET 2000
    root@:/usr/src/sys/compile/GIZMO
Timecounter "i8254" frequency 1193182 Hz
Timecounter "TSC" frequency 267274025 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (267.27-MHz 686-class CPU)
  Origin = "GenuineIntel" Id = 0x633 Stepping = 3

Features=0x80f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,MMX>
real memory = 134205440 (131060K bytes)
avail memory = 127119360 (124140K bytes)
Preloaded elf kernel "kernel" at 0xc0383000.
Pentium Pro MTRR support enabled
md0: Malloc disk
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443LX (440 LX) host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443LX (440 LX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <ATI Mach64-GZ graphics accelerator> at 0.0
isab0: <Intel 82371AB PCI to ISA bridge> at device 4.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0xc800-0xc80f at device 4.1 on
pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
pci0: <Intel 82371AB/EB (PIIX4) USB controller> at 4.2 irq 9
chip1: <Intel 82371AB Power management controller> port 0xe800-0xe80f at
device 4.3 on pci0
ahc0: <Adaptec aic7880 Ultra SCSI adapter> port 0xc000-0xc0ff mem
0xdd800000-0xdd800fff irq 9 at device 6.0 on pci0
aic7880: Wide Channel A, SCSI Id=7, 16/255 SCBs
ed0: <NE2000 PCI Ethernet (RealTek 8029)> port 0xb800-0xb81f irq 11 at
device 11.0 on pci0
ed0: address 00:40:05:48:c3:a7, type NE2000 (16 bit)
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
ppbus0: IEEE1284 device found /NIBBLE
Probing for PnP devices on ppbus0:
ppbus0: <Hewlett-Packard HP LaserJet 6L/0101.01> PRINTER HP ENHANCED
PCL5,PJL
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
isic0: Could not get an irq for AVM A1/Fritz!
i4b: ISDN call control device attached
i4btel: 2 ISDN telephony interface device(s) attached
i4brbch: 4 raw B channel access device(s) attached
i4bctl: ISDN system control port attached
i4btrc: 4 ISDN trace device(s) attached
i4bisppp: 4 ISDN SyncPPP device(s) attached
IP packet filtering initialized, divert enabled, rule-based forwarding
enabled, default to accept, logging limited to 100 packets/entry by default
IP Filter: v3.4.8 initialized. Default = pass all, Logging = enabled
Mounting root from ufs:/dev/da1s2a
da1 at ahc0 bus 0 target 6 lun 0
da1: <IBM DCAS-34330 S65A> Fixed Direct Access SCSI-2 device
da1: 20.000MB/s transfers (20.000MHz, offset 15)
da1: 4134MB (8467200 512 byte sectors: 255H 63S/T 527C)
da0 at ahc0 bus 0 target 1 lun 0
da0: <IBM DDRS-34560 S92A> Fixed Direct Access SCSI-2 device
da0: 20.000MB/s transfers (20.000MHz, offset 15), Tagged Queueing Enabled
da0: 4357MB (8925000 512 byte sectors: 255H 63S/T 555C)
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xc400-0xc41f irq 9 at
device 4.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
cd0 at ahc0 bus 0 target 2 lun 0
cd0: <PLEXTOR CD-ROM PX-32TS 1.02> Removable CD-ROM SCSI-2 device
cd0: 20.000MB/s transfers (20.000MHz, offset 15)
cd0: cd present [70826 x 2048 byte records]

To Unsubscribe: send mail to majordomo(at)de.FreeBSD.org
with "unsubscribe de-bsd-questions" in the body of the message
Received on Tue 05 Dec 2000 - 16:55:46 CET