© 1995-2013 by The FreeBSD Project. All rights reserved.URL: http://lists.de.freebsd.org
Am Mi, 2003-10-15 um 16.12 schrieb Bernd Walter:
> On Wed, Oct 15, 2003 at 03:56:27PM +0200, Marc Santhoff wrote:
[...]
> Was sagt denn jetzt ein boot -v?
Oha, 'ne Menge. Ich habe es ausnahmsweise mal ungekürzt an diese Mail
gepinnt.
Bis später,
Marc
[class=060000] [hdr=80] is there (id=01e010de)
pcibios: BIOS version 2.10
Using $PIR table, 11 entries at 0xc00fdeb0
PCI-Only Interrupts: 5 11
Location Bus Device Pin Link IRQs
slot 1 0 8 A 0x01 3 4 5 7 9 10 11 12 14 15
slot 1 0 8 B 0x02 3 4 5 7 9 10 11 12 14 15
slot 1 0 8 C 0x03 3 4 5 7 9 10 11 12 14 15
slot 1 0 8 D 0x04 3 4 5 7 9 10 11 12 14 15
slot 2 0 12 A 0x01 3 4 5 7 9 10 11 12 14 15
slot 2 0 12 B 0x02 3 4 5 7 9 10 11 12 14 15
slot 2 0 12 C 0x03 3 4 5 7 9 10 11 12 14 15
slot 2 0 12 D 0x04 3 4 5 7 9 10 11 12 14 15
slot 3 255 31 A 0x0f 3 4 5 7 9 10 11 12 14 15
slot 3 255 31 B 0x0f 3 4 5 7 9 10 11 12 14 15
slot 3 255 31 C 0x0f 3 4 5 7 9 10 11 12 14 15
slot 3 255 31 D 0x0f 3 4 5 7 9 10 11 12 14 15
slot 4 1 6 A 0x03 3 4 5 7 9 10 11 12 14 15
slot 4 1 6 B 0x04 3 4 5 7 9 10 11 12 14 15
slot 4 1 6 C 0x01 3 4 5 7 9 10 11 12 14 15
slot 4 1 6 D 0x02 3 4 5 7 9 10 11 12 14 15
slot 5 1 7 A 0x04 3 4 5 7 9 10 11 12 14 15
slot 5 1 7 B 0x01 3 4 5 7 9 10 11 12 14 15
slot 5 1 7 C 0x02 3 4 5 7 9 10 11 12 14 15
slot 5 1 7 D 0x03 3 4 5 7 9 10 11 12 14 15
slot 6 1 8 A 0x01 3 4 5 7 9 10 11 12 14 15
slot 6 1 8 B 0x02 3 4 5 7 9 10 11 12 14 15
slot 6 1 8 C 0x03 3 4 5 7 9 10 11 12 14 15
slot 6 1 8 D 0x04 3 4 5 7 9 10 11 12 14 15
slot 7 1 9 A 0x02 3 4 5 7 9 10 11 12 14 15
slot 7 1 9 B 0x03 3 4 5 7 9 10 11 12 14 15
slot 7 1 9 C 0x04 3 4 5 7 9 10 11 12 14 15
slot 7 1 9 D 0x01 3 4 5 7 9 10 11 12 14 15
slot 8 1 10 A 0x03 3 4 5 7 9 10 11 12 14 15
slot 8 1 10 B 0x04 3 4 5 7 9 10 11 12 14 15
slot 8 1 10 C 0x01 3 4 5 7 9 10 11 12 14 15
slot 8 1 10 D 0x02 3 4 5 7 9 10 11 12 14 15
slot 9 1 11 A 0x04 3 4 5 7 9 10 11 12 14 15
slot 9 1 11 B 0x01 3 4 5 7 9 10 11 12 14 15
slot 9 1 11 C 0x02 3 4 5 7 9 10 11 12 14 15
slot 9 1 11 D 0x03 3 4 5 7 9 10 11 12 14 15
embedded 0 30 A 0x04 3 4 5 7 9 10 11 12 14 15
embedded 0 30 B 0x02 3 4 5 7 9 10 11 12 14 15
embedded 0 30 C 0x02 3 4 5 7 9 10 11 12 14 15
embedded 0 30 D 0x02 3 4 5 7 9 10 11 12 14 15
pcib0: <Host to PCI bridge> at pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pci0: physical bus=0
map[10]: type 3, range 32, base e0000000, size 26, enabled
found-> vendor=0x10de, dev=0x01e0, revid=0xa2
bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x01eb, revid=0xa2
bus=0, slot=0, func=1
class=05-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0020, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x01ee, revid=0xa2
bus=0, slot=0, func=2
class=05-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0020, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x01ed, revid=0xa2
bus=0, slot=0, func=3
class=05-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0020, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x01ec, revid=0xa2
bus=0, slot=0, func=4
class=05-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0020, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x01ef, revid=0xa2
bus=0, slot=0, func=5
class=05-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0020, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10de, dev=0x0060, revid=0xa3
bus=0, slot=1, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x000f, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 4, range 32, base 0000e400, size 5, enabled
found-> vendor=0x10de, dev=0x0064, revid=0xa2
bus=0, slot=1, func=1
class=0c-05-00, hdrtype=0x00, mfdev=1
cmdreg=0x0001, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=a, irq=255
powerspec 2 supports D0 D3 current D0
map[10]: type 1, range 32, base ea080000, size 12, enabled
found-> vendor=0x10de, dev=0x0067, revid=0xa3
bus=0, slot=2, func=0
class=0c-03-10, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=a, irq=255
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base ea083000, size 12, enabled
found-> vendor=0x10de, dev=0x0067, revid=0xa3
bus=0, slot=2, func=1
class=0c-03-10, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=b, irq=255
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base ea086000, size 8, enabled
pci_cfgintr: can't route an interrupt to 0:2 INTC
found-> vendor=0x10de, dev=0x0068, revid=0xa3
bus=0, slot=2, func=2
class=0c-03-20, hdrtype=0x00, mfdev=1
cmdreg=0x0006, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=c, irq=5
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base ea087000, size 12, enabled
map[14]: type 4, range 32, base 0000d000, size 3, enabled
pci_cfgintr: can't route an interrupt to 0:4 INTA
found-> vendor=0x10de, dev=0x0066, revid=0xa1
bus=0, slot=4, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x01 (250 ns), maxlat=0x14 (5000 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 1, range 32, base ea000000, size 19, enabled
pci_cfgintr: can't route an interrupt to 0:5 INTA
found-> vendor=0x10de, dev=0x006b, revid=0xa2
bus=0, slot=5, func=0
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x01 (250 ns), maxlat=0x0c (3000 ns)
intpin=a, irq=5
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type 4, range 32, base 0000d400, size 8, enabled
map[14]: type 4, range 32, base 0000d800, size 7, enabled
map[18]: type 1, range 32, base ea081000, size 12, enabled
pci_cfgintr: can't route an interrupt to 0:6 INTA
found-> vendor=0x10de, dev=0x006a, revid=0xa1
bus=0, slot=6, func=0
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x05 (1250 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
found-> vendor=0x10de, dev=0x006c, revid=0xa3
bus=0, slot=8, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x00a0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x02 (500 ns)
map[20]: type 4, range 32, base 0000f000, size 4, enabled
found-> vendor=0x10de, dev=0x0065, revid=0xa2
bus=0, slot=9, func=0
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
powerspec 2 supports D0 D3 current D0
map[10]: type 1, range 32, base ea084000, size 11, enabled
map[14]: type 1, range 32, base ea085000, size 6, enabled
pci_cfgintr: can't route an interrupt to 0:13 INTA
found-> vendor=0x10de, dev=0x006e, revid=0xa3
bus=0, slot=13, func=0
class=0c-00-10, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns)
intpin=a, irq=11
powerspec 2 supports D0 D1 D2 D3 current D0
found-> vendor=0x10de, dev=0x01e8, revid=0xa2
bus=0, slot=30, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0220, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x0a (2500 ns), maxlat=0x00 (0 ns)
pci0: <memory, RAM> at device 0.1 (no driver attached)
pci0: <memory, RAM> at device 0.2 (no driver attached)
pci0: <memory, RAM> at device 0.3 (no driver attached)
pci0: <memory, RAM> at device 0.4 (no driver attached)
pci0: <memory, RAM> at device 0.5 (no driver attached)
isab0: <PCI-ISA bridge> at device 1.0 on pci0
isa0: <ISA bus> on isab0
pci0: <serial bus, SMBus> at device 1.1 (no driver attached)
ohci0: <OHCI (generic) USB controller> mem 0xea080000-0xea080fff at device 2.0 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTA
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea083000-0xea083fff at device 2.1 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTB
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
pci0: <serial bus, USB> at device 2.2 (no driver attached)
pci0: <network, ethernet> at device 4.0 (no driver attached)
pci0: <multimedia, audio> at device 5.0 (no driver attached)
pci0: <multimedia, audio> at device 6.0 (no driver attached)
pcib1: <PCIBIOS PCI-PCI bridge> at device 8.0 on pci0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xc000-0xcfff
pcib1: memory decode 0xe9000000-0xe9ffffff
pcib1: prefetched decode 0xfff00000-0xfffff
pci1: <PCI bus> on pcib1
pci1: physical bus=1
map[10]: type 4, range 32, base 0000c000, size 8, enabled
map[14]: type 1, range 32, base e9011000, size 8, enabled
pci_cfgintr_valid: BIOS irq 11 is valid
pci_cfgintr: 1:8 INTA BIOS irq 11
found-> vendor=0x1000, dev=0x0001, revid=0x12
bus=1, slot=8, func=0
class=01-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0200, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x40 (16000 ns)
intpin=a, irq=11
map[10]: type 4, range 32, base 0000c400, size 8, enabled
map[14]: type 1, range 32, base e9010000, size 8, enabled
pci_cfgintr_valid: BIOS irq 5 is valid
pci_cfgintr: 1:10 INTA BIOS irq 5
found-> vendor=0x1106, dev=0x3065, revid=0x43
bus=1, slot=10, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x08 (2000 ns)
intpin=a, irq=5
powerspec 2 supports D0 D3 current D0
sym0: <810a> port 0xc000-0xc0ff mem 0xe9011000-0xe90110ff irq 11 at device 8.0 on pci1
pcib1: device sym0 requested decoded memory range 0xe9011000-0xe90110ff
sym0: No NVRAM, ID 7, Fast-10, SE, parity checking
sym0: open drain IRQ line driver
sym0: using LOAD/STORE-based firmware.
pci1: <network, ethernet> at device 10.0 (no driver attached)
atapci0: <nVidia nForce2 UDMA133 controller> port 0xf000-0xf00f at device 9.0 on pci0
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80
ata0-slave: stat=0x00 err=0x4d lsb=0x00 msb=0x00
ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: reset tp2 mask=03 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: reset tp1 mask=03 ostat0=20 ostat1=30
ata1-master: stat=0x20 err=0x20 lsb=0x20 msb=0x20
ata1-slave: stat=0x30 err=0x30 lsb=0x30 msb=0x30
ata1: reset tp2 mask=03 stat0=20 stat1=30 devices=0x0
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
pci0: <serial bus, FireWire> at device 13.0 (no driver attached)
pcib2: <PCI-PCI bridge> at device 30.0 on pci0
pcib2: secondary bus 2
pcib2: subordinate bus 2
pcib2: I/O decode 0xf000-0xfff
pcib2: memory decode 0xe6000000-0xe8ffffff
pcib2: prefetched decode 0xe4000000-0xe5ffffff
pci2: <PCI bus> on pcib2
pci2: physical bus=2
map[10]: type 3, range 32, base e4000000, size 25, enabled
map[14]: type 1, range 32, base e6000000, size 14, enabled
map[18]: type 1, range 32, base e7000000, size 23, enabled
pci_cfgintr_virgin: using routable PCI-only interrupt 5
pci_cfgintr: ROUTE_INTERRUPT failed.
found-> vendor=0x102b, dev=0x0525, revid=0x05
bus=2, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=8 (dwords)
lattimer=0x20 (960 ns), mingnt=0x10 (4000 ns), maxlat=0x20 (8000 ns)
intpin=a, irq=5
powerspec 2 supports D0 D3 current D0
pci2: <display, VGA> at device 0.0 (no driver attached)
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
pnpbios: 17 devices, largest 98 bytes
PNP0000: adding irq mask 0x4
PNP0000: adding io range 0x20-0x21, size=0x2, align=0
PNP0000: adding io range 0xa0-0xa1, size=0x2, align=0
pnpbios: handle 0 device ID PNP0000 (0000d041)
PNP0200: adding dma mask 0x10
PNP0200: adding io range 0-0xf, size=0x10, align=0
PNP0200: adding io range 0x81-0x83, size=0x3, align=0
PNP0200: adding io range 0x87-0x87, size=0x1, align=0
PNP0200: adding io range 0x89-0x8b, size=0x3, align=0
PNP0200: adding io range 0x8f-0x91, size=0x3, align=0
PNP0200: adding io range 0xc0-0xdf, size=0x20, align=0
pnpbios: handle 1 device ID PNP0200 (0002d041)
PNP0100: adding irq mask 0x1
PNP0100: adding io range 0x40-0x43, size=0x4, align=0
pnpbios: handle 2 device ID PNP0100 (0001d041)
PNP0b00: adding irq mask 0x100
PNP0b00: adding io range 0x70-0x71, size=0x2, align=0
pnpbios: handle 3 device ID PNP0b00 (000bd041)
PNP0303: adding irq mask 0x2
PNP0303: adding io range 0x60-0x60, size=0x1, align=0
PNP0303: adding io range 0x64-0x64, size=0x1, align=0
pnpbios: handle 4 device ID PNP0303 (0303d041)
PNP0800: adding io range 0x61-0x61, size=0x1, align=0
pnpbios: handle 5 device ID PNP0800 (0008d041)
PNP0c04: adding irq mask 0x2000
PNP0c04: adding io range 0xf0-0xff, size=0x10, align=0
pnpbios: handle 6 device ID PNP0c04 (040cd041)
PNP0c01: adding fixed memory32 range 0-0x9ffff, size=0xa0000
PNP0c01: adding fixed memory32 range 0xfffe0000-0xffffffff, size=0x20000
PNP0c01: adding fixed memory32 range 0xfec00000-0xfec0ffff, size=0x10000
PNP0c01: adding fixed memory32 range 0xfee00000-0xfee0ffff, size=0x10000
PNP0c01: adding fixed memory32 range 0x100000-0xffffff, size=0xf00000
pnpbios: handle 7 device ID PNP0c01 (010cd041)
PNP0c02: adding fixed memory32 range 0xf0000-0xf3fff, size=0x4000
PNP0c02: adding fixed memory32 range 0xf4000-0xf7fff, size=0x4000
PNP0c02: adding fixed memory32 range 0xf8000-0xfffff, size=0x8000
PNP0c02: adding fixed memory32 range 0xcd800-0xcffff, size=0x2800
pnpbios: handle 8 device ID PNP0c02 (020cd041)
PNP0a03: adding io range 0x294-0x297, size=0x4, align=0
PNP0a03: adding io range 0x4d0-0x4d1, size=0x2, align=0
PNP0a03: adding io range 0xcf8-0xcff, size=0x8, align=0
pnpbios: handle 9 device ID PNP0a03 (030ad041)
PNP0f13: adding irq mask 0x1000
pnpbios: handle 10 device ID PNP0f13 (130fd041)
PNP0501: adding irq mask 0x10
PNP0501: adding io range 0x3f8-0x3ff, size=0x8, align=0
pnpbios: handle 11 device ID PNP0501 (0105d041)
PNP0700: adding dma mask 0x4
PNP0700: adding io range 0x3f0-0x3f5, size=0x6, align=0
PNP0700: adding io range 0x3f7-0x3f7, size=0x1, align=0
PNP0700: adding irq mask 0x40
pnpbios: handle 12 device ID PNP0700 (0007d041)
PNP0401: adding dma mask 0x8
PNP0401: adding irq mask 0x80
PNP0401: adding io range 0x378-0x37f, size=0x8, align=0
PNP0401: adding io range 0x778-0x77f, size=0x8, align=0
pnpbios: handle 14 device ID PNP0401 (0104d041)
PNP0501: adding irq mask 0x8
PNP0501: adding io range 0x2f8-0x2ff, size=0x8, align=0
pnpbios: handle 15 device ID PNP0501 (0105d041)
PNPb006: adding irq mask 0x400
PNPb006: adding io range 0x330-0x331, size=0x2, align=0
pnpbios: handle 16 device ID PNPb006 (06b0d041)
PNPb02f: adding io range 0x201-0x207, size=0x7, align=0
PNPb02f: adding io range 0x200-0x200, size=0x1, align=0
pnpbios: handle 17 device ID PNPb02f (2fb0d041)
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xcc000-0xcd7ff,0xc8000-0xcbfff,0xc0000-0xc7fff on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: current command byte:0047
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse Explorer, device ID 4-00, 5 buttons
psm0: config:00000000, flags:00000000, packet size:4
psm0: syncmask:08, syncbits:08
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/9 bytes threshold
ppbus0: <Parallel port bus> on ppc0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x41 0x51 0x41 0x41
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: irq maps: 0x41 0x49 0x41 0x41
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
adv1: Invalid baseport of 0x20 specified. Nearest valid baseport is 0x100. Failing probe.
adv1: Invalid baseport of 0x0 specified. Nearest valid baseport is 0x100. Failing probe.
adv1: Invalid baseport of 0x40 specified. Nearest valid baseport is 0x100. Failing probe.
adv1: Invalid baseport of 0x70 specified. Nearest valid baseport is 0x100. Failing probe.
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0303> at port 0x60 on isa0
adv1: Invalid baseport of 0x61 specified. Nearest valid baseport is 0x100. Failing probe.
unknown: <PNP0800> failed to probe at port 0x61 on isa0
adv1: Invalid baseport of 0xf0 specified. Nearest valid baseport is 0x100. Failing probe.
adv1: Invalid baseport of 0x294 specified. Nearest valid baseport is 0x330. Failing probe.
unknown: <PNP0f13> can't assign resources (irq)
unknown: <PNP0f13> at irq 12 on isa0
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0501> at port 0x3f8-0x3ff on isa0
unknown: <PNP0700> can't assign resources (port)
unknown: <PNP0700> at port 0x3f0-0x3f5 on isa0
unknown: <PNP0401> can't assign resources (port)
unknown: <PNP0401> at port 0x378-0x37f on isa0
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0501> at port 0x2f8-0x2ff on isa0
unknown: <PNPb006> failed to probe at port 0x330-0x331 irq 10 on isa0
adv1: Invalid baseport of 0x201 specified. Nearest valid baseport is 0x210. Failing probe.
unknown: <PNPb02f> failed to probe at port 0x200,0x201-0x207 on isa0
Device configuration finished.
Timecounter "TSC" frequency 1536823853 Hz quality 800
Timecounters tick every 10.000 msec
lo0: bpf attached
[0] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:80 typ:165 s(CHS):0/0/1 e(CHS):1023/254/63 s:0 l:50000
GEOM: Configure md0a, start 0 length 4423680 end 4423679
GEOM: Configure md0c, start 0 length 4423680 end 4423679
ata0-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ad0: setting UDMA100 on nVidia nForce2 chip
GEOM: create disk ad0 dp=0xc6a12170
ad0: <IC35L060AVV207-0/V22OA63A> ATA-6 disk at ata0-master
ad0: 57220MB (117187500 sectors), 116257 C, 16 H, 63 S, 512 B
ad0: 16 secs/int, 1 depth queue, UDMA100
GEOM: new disk ad0
ar: FreeBSD check1 failed
Waiting 15 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
[0] f:00 typ:6 s(CHS):0/1/1 e(CHS):15/254/63 s:63 l:256977
[1] f:00 typ:15 s(CHS):16/0/1 e(CHS):1023/254/63 s:257040 l:62669565
[2] f:80 typ:165 s(CHS):1023/255/63 e(CHS):1023/254/63 s:62926605 l:46122615
[3] f:00 typ:131 s(CHS):1023/255/63 e(CHS):1023/149/3 s:109049220 l:8138280
GEOM: Configure ad0s1, start 32256 length 131572224 end 131604479
GEOM: Configure ad0s2, start 131604480 length 32086817280 end 32218421759
GEOM: Configure ad0s3, start 32218421760 length 23614778880 end 55833200639
GEOM: Configure ad0s4, start 55833200640 length 4166799360 end 59999999999
MBREXT Slice 5 on ad0s2:
[0] f:00 typ:11 s(CHS):16/1/1 e(CHS):36/254/63 s:63 l:16787862
[1] f:00 typ:5 s(CHS):1023/0/1 e(CHS):1023/254/63 s:16787925 l:16787925
GEOM: Configure ad0s5, start 32256 length 8595385344 end 8595417599
MBREXT Slice 6 on ad0s2:
[0] f:00 typ:7 s(CHS):1023/1/1 e(CHS):1023/254/63 s:63 l:16787862
[1] f:00 typ:5 s(CHS):1023/0/1 e(CHS):1023/254/63 s:33575850 l:29093715
GEOM: Configure ad0s6, start 8595449856 length 8595385344 end 17190835199
MBREXT Slice 7 on ad0s2:
[0] f:00 typ:11 s(CHS):58/1/1 e(CHS):844/254/63 s:63 l:29093652
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad0s7, start 17190867456 length 14895949824 end 32086817279
GEOM: Configure ad0s3a, start 545259520 length 104857600 end 650117119
GEOM: Configure ad0s3b, start 0 length 545259520 end 545259519
GEOM: Configure ad0s3c, start 0 length 23614778880 end 23614778879
GEOM: Configure ad0s3e, start 650117120 length 104857600 end 754974719
GEOM: Configure ad0s3f, start 754974720 length 16416505856 end 17171480575
GEOM: Configure ad0s3g, start 17171480576 length 6443298304 end 23614778879
(probe2:sym0:0:2:0): error 22
(probe2:sym0:0:2:0): Unretryable Error
GEOM: create disk cd0 dp=0xc693ee00
GEOM: new disk cd0
(cd0:sym0:0:2:0): error 6
(cd0:sym0:0:2:0): Unretryable Error
cd0 at sym0 bus 0 target 2 lun 0
cd0: <PLEXTOR CD-ROM PX-40TS 1.11> Removable CD-ROM SCSI-2 device
cd0: 10.000MB/s transfers (10.000MHz, offset 8)
cd0: Attempt to query device size failed: NOT READY,
(cd0:sym0:0:2:0): error 6
(cd0:sym0:0:2:0): Unretryable Error
(cd0:sym0:0:2:0): error 6
(cd0:sym0:0:2:0): Unretryable Error
Mounting root from ufs:/dev/md0
start_init: trying /sbin/init
start_init: trying /sbin/oinit
start_init: trying /sbin/init.bak
start_init: trying /stand/sysinstall
ohci0: <OHCI (generic) USB controller> mem 0xea080000-0xea080fff at device 2.0 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTA
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea083000-0xea083fff at device 2.1 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTB
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea080000-0xea080fff at device 2.0 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTA
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea083000-0xea083fff at device 2.1 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTB
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea080000-0xea080fff at device 2.0 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTA
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea083000-0xea083fff at device 2.1 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTB
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
vr0: <VIA VT6102 Rhine II 10/100BaseTX> port 0xc400-0xc4ff mem 0xe9010000-0xe90100ff irq 5 at device 10.0 on pci1
pcib1: device vr0 requested decoded I/O range 0xc400-0xc4ff
vr0: Ethernet address: 00:50:ba:24:d8:b2
vr0: bpf attached
miibus0: <MII bus> on vr0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: OUI 0x0005be, model 0x0008, rev. 0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ohci0: <OHCI (generic) USB controller> mem 0xea080000-0xea080fff at device 2.0 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTA
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea083000-0xea083fff at device 2.1 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTB
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea080000-0xea080fff at device 2.0 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTA
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea083000-0xea083fff at device 2.1 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTB
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea080000-0xea080fff at device 2.0 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTA
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea083000-0xea083fff at device 2.1 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTB
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea080000-0xea080fff at device 2.0 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTA
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea083000-0xea083fff at device 2.1 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTB
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
adv1: Invalid baseport of 0x61 specified. Nearest valid baseport is 0x100. Failing probe.
adv1: Invalid baseport of 0x201 specified. Nearest valid baseport is 0x210. Failing probe.
ohci0: <OHCI (generic) USB controller> mem 0xea080000-0xea080fff at device 2.0 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTA
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea083000-0xea083fff at device 2.1 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTB
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea080000-0xea080fff at device 2.0 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTA
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea083000-0xea083fff at device 2.1 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTB
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea080000-0xea080fff at device 2.0 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTA
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea083000-0xea083fff at device 2.1 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTB
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea080000-0xea080fff at device 2.0 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTA
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea083000-0xea083fff at device 2.1 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTB
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea080000-0xea080fff at device 2.0 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTA
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea083000-0xea083fff at device 2.1 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTB
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea080000-0xea080fff at device 2.0 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTA
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea083000-0xea083fff at device 2.1 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTB
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea080000-0xea080fff at device 2.0 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTA
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea083000-0xea083fff at device 2.1 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTB
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea080000-0xea080fff at device 2.0 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTA
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea083000-0xea083fff at device 2.1 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTB
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea080000-0xea080fff at device 2.0 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTA
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea083000-0xea083fff at device 2.1 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTB
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
adv1: Invalid baseport of 0x61 specified. Nearest valid baseport is 0x100. Failing probe.
adv1: Invalid baseport of 0x201 specified. Nearest valid baseport is 0x210. Failing probe.
adv1: Invalid baseport of 0x61 specified. Nearest valid baseport is 0x100. Failing probe.
adv1: Invalid baseport of 0x201 specified. Nearest valid baseport is 0x210. Failing probe.
ohci0: <OHCI (generic) USB controller> mem 0xea080000-0xea080fff at device 2.0 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTA
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea083000-0xea083fff at device 2.1 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTB
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea080000-0xea080fff at device 2.0 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTA
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
ohci0: <OHCI (generic) USB controller> mem 0xea083000-0xea083fff at device 2.1 on pci0
pci_cfgintr: can't route an interrupt to 0:2 INTB
ohci0: Could not allocate irq
device_probe_and_attach: ohci0 attach returned 6
(cd0:sym0:0:2:0): error 6
(cd0:sym0:0:2:0): Unretryable Error
fd0: autoselected 1440 KB medium
fd0: autoselected 1440 KB medium
To Unsubscribe: send mail to majordomo.FreeBSD.org
with "unsubscribe de-bsd-questions" in the body of the message
Received on Wed 15 Oct 2003 - 17:33:26 CEST