© 1995-2013 by The FreeBSD Project. All rights reserved.URL: http://lists.de.freebsd.org
Stefan Weißwange wrote:
> Hendrik Scholz wrote:
>> $ ifconfig de8
>> de8: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
>> ^^
>> inet6 fe80::280:c8ff:fee8:4082%de8 prefixlen 64 scopeid 0xa
>> ether 00:80:c8:e8:40:82
>> media: Ethernet 10baseT/UTP
>> status: active
>
>
> Sollte es das schon gewesen sein? *verunsichert* Ich werd' nachschauen,
> sobald ich zu Haus bin.
Stefan hat grad durchgegeben, das war's nicht. Ich häng' mal die logs
an. Ich hoffe, es erschlägt niemanden :-)
> Stefan
So long,
Jens
Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.7-RC #3: Wed Jan 29 14:14:58 CET 2003
root(at)riftergw.muppets.liwing.de:/usr/obj/export/sources/src/sys/RIFTERGW
Timecounter "i8254" frequency 1193182 Hz
CPU: Pentium/P54C (83.70-MHz 586-class CPU)
Origin = "GenuineIntel" Id = 0x525 Stepping = 5
Features=0x3bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,APIC>
real memory = 134217728 (131072K bytes)
avail memory = 127250432 (124268K bytes)
Changing APIC ID for IO APIC #0 from 0 to 2 on chip
Programming 16 pins in IOAPIC #0
IOAPIC #0 intpin 2 -> irq 0
FreeBSD/SMP: Multiprocessor motherboard
cpu0 (BSP): apic id: 0, version: 0x00030010, at 0xfee00000
cpu1 (AP): apic id: 1, version: 0x00030010, at 0xfee00000
io0 (APIC): apic id: 2, version: 0x000f0011, at 0xfec00000
pnpbios: Bad PnP BIOS data checksum
Preloaded elf kernel "kernel" at 0xc0352000.
Intel Pentium detected, installing workaround for F00F bug
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
isab0: <Intel 82375EB PCI-EISA bridge> at device 2.0 on pci0
eisa0: <EISA bus> on isab0
mainboard0: <AMI7111 (System Board)> on eisa0 slot 0
ahc_eisa0: <Adaptec 274X SCSI adapter> at 0x1c00-0x1cff, irq 11 (level)
ahc_eisa0: on eisa0 slot 1
aic7770: Single Channel A, SCSI Id=7, 4/253 SCBs
isa0: <ISA bus> on isab0
atapci0: <CMD 640 ATA controller !WARNING! buggy chip data loss possible> irq 14 at device 3.0 on pci0
atapci0: ATA channel disabled by BIOS
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xfc00-0xfc7f mem 0xffbebf80-0xffbebfff irq 12 at device 6.0 on pci0
xl0: Ethernet address: 00:01:02:9b:c3:29
miibus0: <MII bus> on xl0
xlphy0: <3c905C 10/100 internal PHY> on miibus0
xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci0: <Matrox MGA Millennium 2064W graphics accelerator> at 7.0 irq 9
xl1: <3Com 3c905C-TX Fast Etherlink XL> port 0xf880-0xf8ff mem 0xffbebf00-0xffbebf7f irq 15 at device 8.0 on pci0
xl1: Ethernet address: 00:01:02:0c:7f:77
miibus1: <MII bus> on xl1
xlphy1: <3c905C 10/100 internal PHY> on miibus1
xlphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc87ff,0xd8000-0xdbfff on isa0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
APIC_IO: Testing 8254 interrupt delivery
APIC_IO: routing 8254 via IOAPIC #0 intpin 2
IPsec: Initialized Security Association Processing.
IP Filter: v3.4.29 initialized. Default = block all, Logging = enabled
Waiting 10 seconds for SCSI devices to settle
SMP: AP CPU #1 Launched!
Mounting root from ufs:/dev/da0s1a
da0 at ahc0 bus 0 target 0 lun 0
da0: <SEAGATE ST31230N 0290> Fixed Direct Access SCSI-2 device
da0: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing Enabled
da0: 1010MB (2069860 512 byte sectors: 64H 32S/T 1010C)
da1 at ahc0 bus 0 target 1 lun 0
da1: <SEAGATE ST43400N 1028> Fixed Direct Access SCSI-2 device
da1: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing Enabled
da1: 2777MB (5688447 512 byte sectors: 64H 32S/T 2777C)
xl0: promiscuous mode enabled
xl0: watchdog timeout
no matching session
xl0: watchdog timeout
no matching session
xl0: watchdog timeout
no matching session
xl0: watchdog timeout
no matching session
xl0: watchdog timeout
no matching session
.
.
.
$ cat /etc/ppp/ppp.conf
default:
set device PPPoE:xl0
set MTU 1492
set MRU 1492
set dial
set crtscts off
set speed sync
accept lqr
disable deflate
disable pred1
disable vjcomp
disable acfcomp
disable protocomp
disable dns
set log Phase Chat Connect hdlc LCP IPCP CCP tun command Warning Error Alert
set ifaddr 10.0.0.1/0 10.0.0.2/0 0.0.0.0 0.0.0.0
add default HISADDR
set login
set authname geheim(at)t-online.de
set authkey geheim
Jan 29 16:43:38 riftergw ppp[1130]: tun0: Phase: deflink: carrier -> hangup
Jan 29 16:43:38 riftergw ppp[1130]: tun0: Phase: deflink: Connect time: 5 secs: 0 octets in, 0 octets out
Jan 29 16:43:38 riftergw ppp[1130]: tun0: Phase: deflink: 0 packets in, 0 packets out
Jan 29 16:43:38 riftergw ppp[1130]: tun0: Phase: total 0 bytes/sec, peak 0 bytes/sec on Wed Jan 29 16:43:33 2003
Jan 29 16:43:38 riftergw ppp[1130]: tun0: Phase: deflink: hangup -> opening
Jan 29 16:43:38 riftergw ppp[1130]: tun0: Phase: deflink: Enter pause (10) for redialing.
Jan 29 16:43:48 riftergw ppp[1130]: tun0: Chat: deflink: Redial timer expired.
Jan 29 16:43:49 riftergw ppp[1130]: tun0: Phase: deflink: Connected!
Jan 29 16:43:49 riftergw ppp[1130]: tun0: Phase: deflink: opening -> dial
Jan 29 16:43:49 riftergw ppp[1130]: tun0: Phase: deflink: dial -> carrier
Jan 29 16:43:54 riftergw ppp[1130]: tun0: Phase: deflink: Disconnected!
Jan 29 16:43:54 riftergw ppp[1130]: tun0: Phase: deflink: carrier -> hangup
Jan 29 16:43:54 riftergw ppp[1130]: tun0: Phase: deflink: Connect time: 5 secs: 0 octets in, 0 octets out
Jan 29 16:43:54 riftergw ppp[1130]: tun0: Phase: deflink: 0 packets in, 0 packets out
Jan 29 16:43:54 riftergw ppp[1130]: tun0: Phase: total 0 bytes/sec, peak 0 bytes/sec on Wed Jan 29 16:43:49 2003
Jan 29 16:43:54 riftergw ppp[1130]: tun0: Phase: deflink: hangup -> opening
Jan 29 16:43:54 riftergw ppp[1130]: tun0: Phase: deflink: Enter pause (10) for redialing.
Jan 29 16:44:04 riftergw ppp[1130]: tun0: Chat: deflink: Redial timer expired.
Jan 29 16:44:04 riftergw ppp[1130]: tun0: Phase: deflink: Connected!
Jan 29 16:44:04 riftergw ppp[1130]: tun0: Phase: deflink: opening -> dial
Jan 29 16:44:04 riftergw ppp[1130]: tun0: Phase: deflink: dial -> carrier
Jan 29 16:44:09 riftergw ppp[1130]: tun0: Phase: deflink: Disconnected!
Jan 29 16:44:09 riftergw ppp[1130]: tun0: Phase: deflink: carrier -> hangup
Jan 29 16:44:09 riftergw ppp[1130]: tun0: Phase: deflink: Connect time: 5 secs: 0 octets in, 0 octets out
Jan 29 16:44:09 riftergw ppp[1130]: tun0: Phase: deflink: 0 packets in, 0 packets out
Jan 29 16:44:09 riftergw ppp[1130]: tun0: Phase: total 0 bytes/sec, peak 0 bytes/sec on Wed Jan 29 16:44:04 2003
Jan 29 16:44:09 riftergw ppp[1130]: tun0: Phase: deflink: hangup -> opening
Jan 29 16:44:09 riftergw ppp[1130]: tun0: Phase: deflink: Enter pause (10) for redialing.
Jan 29 16:44:19 riftergw ppp[1130]: tun0: Chat: deflink: Redial timer expired.
Jan 29 16:44:19 riftergw ppp[1130]: tun0: Phase: deflink: Connected!
Jan 29 16:44:19 riftergw ppp[1130]: tun0: Phase: deflink: opening -> dial
Jan 29 16:44:19 riftergw ppp[1130]: tun0: Phase: deflink: dial -> carrier
Jan 29 16:44:24 riftergw ppp[1130]: tun0: Phase: deflink: Disconnected!
Jan 29 16:44:24 riftergw ppp[1130]: tun0: Phase: deflink: carrier -> hangup
Jan 29 16:44:24 riftergw ppp[1130]: tun0: Phase: deflink: Connect time: 5 secs: 0 octets in, 0 octets out
Jan 29 16:44:24 riftergw ppp[1130]: tun0: Phase: deflink: 0 packets in, 0 packets out
Jan 29 16:44:24 riftergw ppp[1130]: tun0: Phase: total 0 bytes/sec, peak 0 bytes/sec on Wed Jan 29 16:44:19 2003
Jan 29 16:44:24 riftergw ppp[1130]: tun0: Phase: deflink: hangup -> opening
Jan 29 16:44:24 riftergw ppp[1130]: tun0: Phase: deflink: Enter pause (10) for redialing.
Jan 29 16:44:34 riftergw ppp[1130]: tun0: Chat: deflink: Redial timer expired.
Jan 29 16:44:34 riftergw ppp[1130]: tun0: Phase: deflink: Connected!
Jan 29 16:44:34 riftergw ppp[1130]: tun0: Phase: deflink: opening -> dial
Jan 29 16:44:34 riftergw ppp[1130]: tun0: Phase: deflink: dial -> carrier
Jan 29 16:44:39 riftergw ppp[1130]: tun0: Phase: deflink: Disconnected!
Jan 29 16:44:39 riftergw ppp[1130]: tun0: Phase: deflink: carrier -> hangup
Jan 29 16:44:39 riftergw ppp[1130]: tun0: Phase: deflink: Connect time: 5 secs: 0 octets in, 0 octets out
Jan 29 16:44:39 riftergw ppp[1130]: tun0: Phase: deflink: 0 packets in, 0 packets out
Jan 29 16:44:39 riftergw ppp[1130]: tun0: Phase: total 0 bytes/sec, peak 0 bytes/sec on Wed Jan 29 16:44:34 2003
Jan 29 16:44:39 riftergw ppp[1130]: tun0: Phase: deflink: hangup -> opening
Jan 29 16:44:39 riftergw ppp[1130]: tun0: Phase: deflink: Enter pause (10) for redialing.
# RIFTERGW KERNELCONF INIT 20020707
machine i386
cpu I586_CPU
ident RIFTERGW
maxusers 0
options FFS #Berkeley Fast Filesystem
options FFS_ROOT #FFS usable as root device [keep this!]
options SOFTUPDATES #Enable FFS soft updates support
options UFS_DIRHASH #Improve performance on big directories
options NFS #Network Filesystem
options NFS_NOSERVER
options PROCFS #Process filesystem
options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!]
options SCSI_DELAY=10000 #Delay (in ms) before probing SCSI
options USERCONFIG #boot -c editor
options VISUAL_USERCONFIG #visual boot -c editor
options KTRACE #ktrace(1) support
options SYSVSHM #SYSV-style shared memory
options SYSVMSG #SYSV-style message queues
options SYSVSEM #SYSV-style semaphores
options P1003_1B #Posix P1003_1B real-time extensions
options _KPOSIX_PRIORITY_SCHEDULING
options ICMP_BANDLIM #Rate limit bad replies
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
options SMP
options APIC_IO
device isa
device eisa
device pci
# Floppy drives
device fdc0 at isa? port IO_FD1 irq 6 drq 2
device fd0 at fdc0 drive 0
# ATA and ATAPI devices
device ata0 at isa? port IO_WD1 irq 14
device ata
device atapifd # ATAPI floppy drives
# SCSI Controllers
device ahc # AHA 29xx/EISA 274x
# SCSI peripherals
device scbus # SCSI bus (required)
device da # Direct Access (disks)
device pass # Passthrough device (direct SCSI access)
# atkbdc0 controls both the keyboard and the PS/2 mouse
device atkbdc0 at isa? port IO_KBD
device atkbd0 at atkbdc? irq 1 flags 0x1
device psm0 at atkbdc? irq 12
device vga0 at isa?
# splash screen/screen saver
pseudo-device splash
# syscons is the default console driver, resembling an SCO console
device sc0 at isa? flags 0x100
# Floating point support - do not disable.
device npx0 at nexus? port IO_NPX irq 13
# PCI Ethernet NICs that use the common MII bus controller code.
# NOTE: Be sure to keep the 'device miibus' line in order to use these NICs!
device miibus # MII bus support
device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
# Pseudo devices - the number indicates how many units to allocate.
pseudo-device loop # Network loopback
pseudo-device ether # Ethernet support
pseudo-device tun # Packet tunnel.
pseudo-device pty # Pseudo-ttys (telnet etc)
# The `bpf' pseudo-device enables the Berkeley Packet Filter.
# Be aware of the administrative consequences of enabling this!
pseudo-device bpf #Berkeley packet filter
# net stuff
options INET #Internet communications protocols
options IPSEC #IP security
options IPSEC_ESP #IP security (crypto; define w/ IPSEC)
# DSL Stuff
options NETGRAPH
options NETGRAPH_ASYNC
options NETGRAPH_ETHER
options NETGRAPH_SOCKET
options NETGRAPH_PPPOE
options IPFILTER #ipfilter support
options IPFILTER_LOG #ipfilter logging
options IPFILTER_DEFAULT_BLOCK #block all packets by default
options IPSTEALTH #support for stealth forwarding
options RANDOM_IP_ID
FreeBSD riftergw.muppets.liwing.de 4.7-RC FreeBSD 4.7-RC #2: Tue Jan 28 13:47:16 CET 2003 root@:/usr/obj/export/sources/src/sys/RIFTERGW i386
To Unsubscribe: send mail to majordomo(at)de.FreeBSD.org
with "unsubscribe de-bsd-questions" in the body of the message
Received on Fri 31 Jan 2003 - 00:40:23 CET