XFree86 v. 4.0x configuration

From: Christoph Sold <so(at)server.i-clue.de>
Date: Wed, 11 Apr 2001 18:09:06 +0200

Hi Folks,

habe mir gerade XF86 4 installiert. Hardware ist eine ATI 3D Rage IIc
AGP, Videospeicher 2MB. XF86 will nur 800x600 Screen zulassen. Irgendwas
ist wohl an meiner Konfiguration falsch, ich kapier aber nicht was.

Hier ein paar Ausschnitte:

---<XF86Conf>---
Section "Monitor"
        [...snip...]
        HorizSync 31.5 - 64.3
        VertRefresh 50.0 - 100.0
EndSection

Section "Device"
        Identifier "Card0"
        Driver "ati"
        VendorName "ATI"
        BoardName "Mach64 GW"
        ChipSet "ati"
        ChipId 0x4757
        ChipRev 0x7a
        BusID "PCI:1:0:0"
EndSection

Section "Screen"
        Identifier "Screen0"
        Device "Card0"
        Monitor "Monitor0"
        DefaultDepth 16
        [SNIP]
        SubSection "Display"
                Depth 15
                Modes "1152x864" "1024x768" "800x600"
        EndSubSection
        SubSection "Display"
                Depth 16
                Modes "1024x768"
        EndSubSection
        [snip]
EndSection
---</XF86Conf>---

---<startx.out>---
XFree86 Version 4.0.3 / X Window System
(protocol Version 11, revision 0, vendor release 6400)
Release Date: 16 March 2001
[snip]
(--) ATI(0): 2048 kB of SGRAM (1:1) detected.
[snip]
(II) ATI(0): Supported VESA Video Modes:
(II) ATI(0): 640x480(at)60Hz
(II) ATI(0): 640x480(at)67Hz
(II) ATI(0): 640x480(at)75Hz
(II) ATI(0): 800x600(at)56Hz
(II) ATI(0): 800x600(at)60Hz
(II) ATI(0): 800x600(at)75Hz
(II) ATI(0): 832x624(at)75Hz
(II) ATI(0): 1024x768(at)87Hz (interlaced)
(II) ATI(0): 1024x768(at)60Hz
(II) ATI(0): 1024x768(at)70Hz
(II) ATI(0): 1024x768(at)75Hz
[snip]
(WW) ATI(0): Default mode "1024x768" deleted (insufficient memory for
mode)
(WW) ATI(0): Default mode "1024x768" deleted (insufficient memory for
mode)
(WW) ATI(0): Default mode "1024x768" deleted (insufficient memory for
mode)
(WW) ATI(0): Default mode "1024x768" deleted (insufficient memory for
mode)
(WW) ATI(0): Default mode "1024x768" deleted (insufficient memory for
mode)
(WW) ATI(0): Default mode "1152x864" deleted (insufficient memory for
mode)
(WW) ATI(0): Default mode "1280x960" deleted (insufficient memory for
mode)
(WW) ATI(0): Default mode "1280x960" deleted (insufficient memory for
mode)
[snip]
---<startx.out>---

2MB Video-RAM sollten doch meiner Berechnung nach Problemlos für
1024x768x16 bit reichen?

Tips?

Danke schon im Voraus
-Christoph Sold

Anhang: xf86.conf, startx.out (output von startx)

XFree86 Version 4.0.3 / X Window System
(protocol Version 11, revision 0, vendor release 6400)
Release Date: 16 March 2001
        If the server is older than 6-12 months, or if your card is
        newer than the above date, look for a newer version before
        reporting problems. (See http://www.XFree86.Org/FAQ)
Operating System: FreeBSD 4.3-RC i386 [ELF]
Module Loader present
(==) Log file: "/var/log/XFree86.0.log", Time: Wed Apr 11 17:53:45 2001
(==) Using config file: "/root/XF86Config"
Markers: (--) probed, (**) from config file, (==) default setting,
         (++) from command line, (!!) notice, (II) informational,
         (WW) warning, (EE) error, (??) unknown.
(==) ServerLayout "XFree86 Configured"
(**) |-->Screen "Screen0" (0)
(**) | |-->Monitor "Monitor0"
(**) | |-->Device "Card0"
(**) |-->Input Device "Mouse0"
(**) |-->Input Device "Keyboard0"
(**) XKB: model: "pc105"
(**) XKB: layout: "de"
(**) FontPath set to "/usr/X11R6/lib/X11/fonts/misc/,/usr/X11R6/lib/X11/fonts/Speedo/,/usr/X11R6/lib/X11/fonts/Type1/,/usr/X11R6/lib/X11/fonts/CID/,/usr/X11R6/lib/X11/fonts/75dpi/,/usr/X11R6/lib/X11/fonts/100dpi/"
(**) RgbPath set to "/usr/X11R6/lib/X11/rgb"
(**) ModulePath set to "/usr/X11R6/lib/modules"
(--) Using syscons driver with X support (version 2.0)
(--) using VT number 9

(II) Loading /usr/X11R6/lib/modules/fonts/libbitmap.a
(II) Module bitmap: vendor="The XFree86 Project"
        compiled for 4.0.3, module version = 1.0.0
(II) Loading /usr/X11R6/lib/modules/libpcidata.a
(II) Module pcidata: vendor="The XFree86 Project"
        compiled for 4.0.3, module version = 0.1.0
(II) Loading /usr/X11R6/lib/modules/libscanpci.a
(II) Module scanpci: vendor="The XFree86 Project"
        compiled for 4.0.3, module version = 0.1.0
(II) Unloading /usr/X11R6/lib/modules/libscanpci.a
(--) PCI:*(1:0:0) ATI Mach64 GW rev 122, Mem @ 0xfc000000/24, 0xfbfff000/12, I/O @ 0xec00/8
(II) Loading /usr/X11R6/lib/modules/extensions/libextmod.a
(II) Module extmod: vendor="The XFree86 Project"
        compiled for 4.0.3, module version = 1.0.0
(II) Loading /usr/X11R6/lib/modules/extensions/libxie.a
(II) Module xie: vendor="The XFree86 Project"
        compiled for 4.0.3, module version = 1.0.0
(II) Loading /usr/X11R6/lib/modules/extensions/libpex5.a
(II) Module pex5: vendor="The XFree86 Project"
        compiled for 4.0.3, module version = 1.0.0
(II) Loading /usr/X11R6/lib/modules/extensions/libglx.a
(II) Module glx: vendor="The XFree86 Project"
        compiled for 4.0.3, module version = 1.0.0
(II) Loading /usr/X11R6/lib/modules/extensions/libGLcore.a
(II) Module GLcore: vendor="The XFree86 Project"
        compiled for 4.0.3, module version = 1.0.0
(II) Loading /usr/X11R6/lib/modules/extensions/libdri.a
(II) Module dri: vendor="The XFree86 Project"
        compiled for 4.0.3, module version = 1.0.0
(II) Loading /usr/X11R6/lib/modules/freebsd/libdrm.a
(II) Module drm: vendor="The XFree86 Project"
        compiled for 4.0.3, module version = 1.0.0
(II) Loading /usr/X11R6/lib/modules/extensions/libdbe.a
(II) Module dbe: vendor="The XFree86 Project"
        compiled for 4.0.3, module version = 1.0.0
(II) Loading /usr/X11R6/lib/modules/extensions/librecord.a
(II) Module record: vendor="The XFree86 Project"
        compiled for 4.0.3, module version = 1.13.0
(II) Loading /usr/X11R6/lib/modules/drivers/ati_drv.o
(II) Module ati: vendor="The XFree86 Project"
        compiled for 4.0.3, module version = 6.2.3
(II) Loading /usr/X11R6/lib/modules/input/mouse_drv.o
(II) Module mouse: vendor="The XFree86 Project"
        compiled for 4.0.3, module version = 1.0.0
(II) ATI: ATI driver (version 6.2.3) for chipsets: ati, ativga
(II) R128: Driver for ATI Rage 128 chipsets: ATI Rage 128 RE (PCI),
        ATI Rage 128 RF (AGP), ATI Rage 128 RG (AGP), ATI Rage 128 RK (PCI),
        ATI Rage 128 RL (AGP), ATI Rage 128 Pro PD (AGP),
        ATI Rage 128 Pro PF (AGP), ATI Rage 128 Mobility LE (PCI),
        ATI Rage 128 Mobility LF (AGP), ATI Rage 128 Mobility MF (AGP),
        ATI Rage 128 Mobility ML (AGP)
(II) RADEON: Driver for ATI Radeon chipsets: ATI Radeon QD (AGP),
        ATI Radeon QE (AGP), ATI Radeon QF (AGP), ATI Radeon QG (AGP)
(II) Loading /usr/X11R6/lib/modules/drivers/atimisc_drv.o
(II) Module ati: vendor="The XFree86 Project"
        compiled for 4.0.3, module version = 6.2.3
(==) ATI(0): Chipset: "ati".
(**) ATI(0): Depth 24, (--) framebuffer bpp 32
(II) Loading /usr/X11R6/lib/modules/libint10.a
(II) Module int10: vendor="The XFree86 Project"
        compiled for 4.0.3, module version = 1.0.0
(==) ATI(0): Write-combining range (0xa0000,0x20000) was already clear
(==) ATI(0): Write-combining range (0xf0000,0x10000)
(II) ATI(0): Primary V_BIOS segment is: 0xc000
(II) Loading /usr/X11R6/lib/modules/libddc.a
(II) Module ddc: vendor="The XFree86 Project"
        compiled for 4.0.3, module version = 1.0.0
(II) Loading /usr/X11R6/lib/modules/libvbe.a
(II) Module vbe: vendor="The XFree86 Project"
        compiled for 4.0.3, module version = 1.0.0
(II) ATI(0): VESA BIOS detected
(II) ATI(0): VESA VBE DDC supported
(II) ATI(0): Manufacturer: PHL Model: 2800 Serial#: 94897
(II) ATI(0): Year: 1996 Week: 25
(II) ATI(0): EDID Version: 1.0
(II) ATI(0): Analog Display Input, Input Voltage Level: 0.714/0.286 V
(II) ATI(0): Sync: Separate Composite SyncOnGreen
(II) ATI(0): Max H-Image Size [cm]: horiz.: 30 vert.: 23
(II) ATI(0): Gamma: 3.00
(II) ATI(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display
(II) ATI(0): redX: 0.635 redY: 0.333 greenX: 0.280 greenY: 0.595
(II) ATI(0): blueX: 0.152 blueY: 0.063 whiteX: 0.281 whiteY: 0.311
(II) ATI(0): Supported VESA Video Modes:
(II) ATI(0): 640x480(at)60Hz
(II) ATI(0): 640x480(at)67Hz
(II) ATI(0): 640x480(at)75Hz
(II) ATI(0): 800x600(at)56Hz
(II) ATI(0): 800x600(at)60Hz
(II) ATI(0): 800x600(at)75Hz
(II) ATI(0): 832x624(at)75Hz
(II) ATI(0): 1024x768(at)87Hz (interlaced)
(II) ATI(0): 1024x768(at)60Hz
(II) ATI(0): 1024x768(at)70Hz
(II) ATI(0): 1024x768(at)75Hz
(II) ATI(0): Manufacturer's mask: 0
(II) ATI(0): Supported Future Video Modes:
(II) ATI(0): #0: hsize: 640 vsize 480 refresh: 70 vid: 18993
(II) ATI(0): Supported additional Video Mode:
(II) ATI(0): clock: 107.8 MHz Image Size: 288 x 230 mm
(II) ATI(0): h_active: 1280 h_sync: 1360 h_sync_end 1468 h_blank_end 1684 h_border: 0
(II) ATI(0): v_active: 1024 v_sync: 1025 v_sync_end 1030 v_blanking: 1067 v_border: 0
(==) ATI(0): Write-combining range (0xa0000,0x10000) was already clear
(==) ATI(0): Write-combining range (0xfbfff000,0x1000) was already clear
(--) ATI(0): ATI 3D Rage IIc graphics controller detected.
(--) ATI(0): Chip type 4757 "GW", version 2, foundry UMC, class 0, revision 0x01.
(--) ATI(0): AGP bus interface detected; block I/O base is 0xEC00.
(--) ATI(0): ATI Mach64 adapter detected.
(--) ATI(0): Internal RAMDAC (subtype 1) detected.
(==) ATI(0): RGB weight 888
(==) ATI(0): Default visual is TrueColor
(==) ATI(0): Using gamma correction (1.0, 1.0, 1.0)
(II) ATI(0): Using Mach64 accelerator CRTC.
(II) ATI(0): Using 8 MB linear aperture at 0xFC000000.
(II) ATI(0): Using Block 0 MMIO aperture at 0xFBFFF400.
(II) ATI(0): Using Block 1 MMIO aperture at 0xFBFFF000.
(==) ATI(0): Write-combining range (0xa0000,0x10000) was already clear
(==) ATI(0): Write-combining range (0xfc000000,0x200000)
(==) ATI(0): Write-combining range (0xfbfff000,0x1000) was already clear
(II) ATI(0): MMIO write caching enabled.
(--) ATI(0): 2048 kB of SGRAM (1:1) detected.
(WW) ATI(0): Cannot shadow an accelerated frame buffer.
(--) ATI(0): Internal programmable clock generator detected.
(--) ATI(0): Reference clock 157.5/11 (14.318) MHz.
(II) ATI(0): Monitor0: Using hsync range of 31.50-64.30 kHz
(II) ATI(0): Monitor0: Using vrefresh range of 50.00-100.00 Hz
(II) ATI(0): Maximum clock: 166.00 MHz
(WW) ATI(0): Default mode "1024x768" deleted (insufficient memory for mode)
(WW) ATI(0): Default mode "1024x768" deleted (insufficient memory for mode)
(WW) ATI(0): Default mode "1024x768" deleted (insufficient memory for mode)
(WW) ATI(0): Default mode "1024x768" deleted (insufficient memory for mode)
(WW) ATI(0): Default mode "1024x768" deleted (insufficient memory for mode)
(WW) ATI(0): Default mode "1152x864" deleted (insufficient memory for mode)
(WW) ATI(0): Default mode "1280x960" deleted (insufficient memory for mode)
(WW) ATI(0): Default mode "1280x960" deleted (insufficient memory for mode)
(WW) ATI(0): Default mode "1280x1024" deleted (insufficient memory for mode)
(WW) ATI(0): Default mode "1280x1024" deleted (insufficient memory for mode)
(WW) ATI(0): Default mode "1280x1024" deleted (insufficient memory for mode)
(WW) ATI(0): Default mode "1600x1200" deleted (insufficient memory for mode)
(WW) ATI(0): Default mode "1600x1200" deleted (insufficient memory for mode)
(WW) ATI(0): Default mode "1600x1200" deleted (insufficient memory for mode)
(WW) ATI(0): Default mode "1600x1200" deleted (insufficient memory for mode)
(WW) ATI(0): Default mode "1600x1200" deleted (insufficient memory for mode)
(WW) ATI(0): Default mode "1792x1344" deleted (insufficient memory for mode)
(WW) ATI(0): Default mode "1792x1344" deleted (insufficient memory for mode)
(WW) ATI(0): Default mode "1856x1392" deleted (insufficient memory for mode)
(WW) ATI(0): Default mode "1856x1392" deleted (insufficient memory for mode)
(WW) ATI(0): Default mode "1920x1440" deleted (insufficient memory for mode)
(WW) ATI(0): Default mode "1920x1440" deleted (insufficient memory for mode)
(WW) ATI(0): Mode "1152x864" deleted (no mode of this name)
(WW) ATI(0): Mode "1024x768" deleted (no mode of this name)
(--) ATI(0): Virtual size is 800x600 (pitch 800)
(**) ATI(0): Default mode "800x600": 56.3 MHz, 53.7 kHz, 85.1 Hz
(--) ATI(0): Display dimensions: (30, 23) cm
(--) ATI(0): DPI set to (67, 66)
(II) Loading /usr/X11R6/lib/modules/libxaa.a
(II) Module xaa: vendor="The XFree86 Project"
        compiled for 4.0.3, module version = 1.0.0
(II) Loading /usr/X11R6/lib/modules/libcfb32.a
(II) Module cfb32: vendor="The XFree86 Project"
        compiled for 4.0.3, module version = 1.0.0
(II) Loading /usr/X11R6/lib/modules/libcfb.a
(II) Module cfb: vendor="The XFree86 Project"
        compiled for 4.0.3, module version = 1.0.0
(II) Loading /usr/X11R6/lib/modules/libmfb.a
(II) Module mfb: vendor="The XFree86 Project"
        compiled for 4.0.3, module version = 1.0.0
(--) Depth 24 pixmap format is 32 bpp
(==) ATI(0): Write-combining range (0xa0000,0x10000) was already clear
(==) ATI(0): Write-combining range (0xfc000000,0x200000)
(==) ATI(0): Write-combining range (0xfbfff000,0x1000) was already clear
(II) ATI(0): Using XFree86 Acceleration Architecture (XAA)
        Screen to screen bit blits
        Solid filled rectangles
        8x8 mono pattern filled rectangles
        Indirect CPU to Screen color expansion
        Solid Lines
        Offscreen Pixmaps
        Setting up tile and stipple cache:
                7 32x55 slots
(==) ATI(0): Backing store disabled
(**) Mouse0: Protocol: "Auto"
(**) Mouse0: Core Pointer
(==) Mouse0: Buttons: 3
(II) Keyboard "Keyboard0" handled by legacy driver
(II) XINPUT: Adding extended input device "Mouse0" (type: MOUSE)
Could not init font path element /usr/X11R6/lib/X11/fonts/Speedo/, removing from list!
Could not init font path element /usr/X11R6/lib/X11/fonts/Type1/, removing from list!

waiting for X server to shut down

Section "ServerLayout"
        Identifier "XFree86 Configured"
        Screen 0 "Screen0" 0 0
        InputDevice "Mouse0" "CorePointer"
        InputDevice "Keyboard0" "CoreKeyboard"
EndSection

Section "Files"
# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.

RgbPath "/usr/X11R6/lib/X11/rgb"

# ModulePath can be used to set a search path for the X server modules.

ModulePath "/usr/X11R6/lib/modules"

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)

        FontPath "/usr/X11R6/lib/X11/fonts/misc/"
        FontPath "/usr/X11R6/lib/X11/fonts/Speedo/"
        FontPath "/usr/X11R6/lib/X11/fonts/Type1/"
        FontPath "/usr/X11R6/lib/X11/fonts/CID/"
        FontPath "/usr/X11R6/lib/X11/fonts/75dpi/"
        FontPath "/usr/X11R6/lib/X11/fonts/100dpi/"
EndSection

# **********************************************************************
# Module section -- this is an optional section which is used to specify
# which run-time loadable modules to load when the X server starts up.
# **********************************************************************

Section "Module"
        Load "extmod"
        Load "xie"
        Load "pex5"
        Load "glx"
        Load "dri"
        Load "GLcore"

# This loads the DBE extension module.
Load "dbe"

Load "record"

# This loads the Type1 and FreeType font modules
Load "type1"
Load "freetype"

EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************

Section "InputDevice"
        Identifier "Keyboard0"
        Driver "keyboard"
        Option "XkbModel" "pc105"
        Option "XkbLayout" "de"
        Option "XkbVariant" "nodeadkeys"
EndSection

# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************

Section "InputDevice"
        Identifier "Mouse0"
        Driver "mouse"
        Option "Protocol" "Auto"
        Option "Device" "/dev/sysmouse"
EndSection

# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"
        Identifier "Monitor0"
        VendorName "PHL"
        ModelName "2800"
        HorizSync 31.5 - 64.3
        VertRefresh 50.0 - 100.0
        Option "dpms"
EndSection

Section "Screen"
        Identifier "Screen0"
        Device "Card0"
        Monitor "Monitor0"
        DefaultDepth 16
        SubSection "Display"
                Depth 1
        EndSubSection
        SubSection "Display"
                Depth 4
        EndSubSection
        SubSection "Display"
                Depth 8
        EndSubSection
        SubSection "Display"
                Depth 15
                Modes "1152x864" "1024x768" "800x600"
        EndSubSection
        SubSection "Display"
                Depth 16
                Modes "1024x768"
        EndSubSection
        SubSection "Display"
                Depth 24
                Modes "1152x864" "1024x768" "800x600"
        EndSubSection
EndSection

Section "DRI"
EndSection

To Unsubscribe: send mail to majordomo(at)de.FreeBSD.org
with "unsubscribe de-bsd-questions" in the body of the message
Received on Wed 11 Apr 2001 - 18:07:44 CEST