Re: Fünf Port NIC: VIA Rhine III, nur ein Port verfügbar?

From: Timm Wimmers <timm(at)ticore.de>
Date: Tue, 04 Nov 2008 16:33:34 +0100

Bernd Walter schrieb:
> On Tue, Nov 04, 2008 at 03:25:08PM +0100, Bernd Walter wrote:
>> On Tue, Nov 04, 2008 at 03:22:37PM +0100, Bernd Walter wrote:
>>> On Tue, Nov 04, 2008 at 03:05:07PM +0100, Timm Wimmers wrote:
>>>> Moin zusammen,
>>>>
>>>> ich würde hier gern ein PFsense zu Ausbildungszwecken mit der genannten
>>>> Karte einsetzen. PFsense aka FreeBSD erkennt die Karte zwar, stellt aber
>>>> nur einen Port der Karte als vr0 bereit.
>>>>
>>>> dmesg sagt:
>>>> vr0: <VIA VT6105M Rhine III 10/100BaseTX> port 0xd000-0xd0ff mem
>>>> 0xe2000000-0xe20000ff irq 10 at device 10.0 on pci0
>>>>
>>>> Wo muss/kann ich schrauben, dass vr1 bis vr4 zur Verfügung stehen?
>>> Das ist vermutlich eine Karte mit nur einem Netzwerkchip und einem
>>> VLAN fähigem Switch.
>>> In dem Fall musst wissen wie der Switch konfioguriert ist und
>>> FreeBSD-seitig passende VLAN einstellen.
>>> Falls der Switch überhaupt auf VLANs voreingestellt ist und nicht erst
>>> durch einen passenden Treiber konfiguriert werden muss.
>>> Kannst du mal beschreiben was da für große ICs drauf sind?
>> Hat sich erübrigt - der VR-Chip melded sich auf pci0, also steckt
>> der garantiert nicht hinter einer PCI-PCI Bridge, somit kann es auch nur
>> einen Netzwerkchip auf der Karte geben und das Teil ist somit garantiert
>> eine mit integriertem Switch.
>
> Ich denke gerade stückchenweise...
> Schicke trotzdem mal den vollen dmesg Abschnitt der Karte.
> Du hast nämlich vergessen die Meldungen vom PHY zu schicken.
> Und doch mal die Typenbezeichnugnen der großen Chips mailen.
> Evtl gibt es ja Doku dazu - für den RTL8305SC habe ich z.B. den
> rlswitch Treiber geschrieben, weil ich den Chip selber auf reichlich
> verbaut habe.
> Der hat aber nur 5-Ports, also nur 4 nach außen und wird bei dir
> nicht drauf sein.

Oh, ich nehme die Infos auch gern stückchenweise. :)

Produkt: LevelOne FNC-0600TXM 5-port L2 SNMP Switch Card - 5 Anschlüsse

Großer Chip Nr. 1: VIA VT6105M - 0617CD TAIWAN - 23B5000500 (G) (C) (M)
Großer Chip Nr. 2: IC+ IP178C LF - 0738SH13 - FOS7262.1
EEPROM: AF0727 - 93BC46 - PNGMG

**********************
* dmesg *
**********************
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-RELEASE-p11 #0: Sun Feb 24 16:32:58 EST 2008
    sullrich(at)builder6.pfsense.com:/usr/obj.pfSense/usr/src/sys/pfSense.6
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Athlon(tm) XP 2200+ (1800.07-MHz 686-class CPU)
  Origin = "AuthenticAMD" Id = 0x680 Stepping = 0

Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
  AMD Features=0xc0400800<SYSCALL,MMX+,3DNow+,3DNow>
real memory = 1073676288 (1023 MB)
avail memory = 1041670144 (993 MB)
wlan: mac acl policy registered
kbd1 at kbdmux0
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
acpi0: <GBT AWRDACPI> on motherboard
acpi0: Power Button (fixed)
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
acpi_button0: <Power Button> on acpi0
acpi_button1: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port
0xcf8-0xcff,0x4000-0x407f,0x4080-0x40ff,0x5000-0x500f on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <VIA 8377 (Apollo KT400/KT400A/KT600) host to PCI bridge> mem
0xd0000000-0xd7ffffff at device 0.0 on pci0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
vr0: <VIA VT6105M Rhine III 10/100BaseTX> port 0xd000-0xd0ff mem
0xe2000000-0xe20000ff irq 10 at device 10.0 on pci0
miibus0: <MII bus> on vr0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
vr0: Ethernet address: 00:11:6b:d0:2c:b8
pci0: <multimedia, audio> at device 11.0 (no driver attached)
uhci0: <VIA 83C572 USB controller> port 0xd800-0xd81f irq 11 at device
16.0 on pci0
uhci0: [GIANT-LOCKED]
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0xdc00-0xdc1f irq 11 at device
16.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <VIA 83C572 USB controller> port 0xe000-0xe01f irq 10 at device
16.2 on pci0
uhci2: [GIANT-LOCKED]
usb2: <VIA 83C572 USB controller> on uhci2
usb2: USB revision 1.0
uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0: <VIA VT6202 USB 2.0 controller> mem 0xe2001000-0xe20010ff irq 5
at device 16.3 on pci0
ehci0: [GIANT-LOCKED]
usb3: EHCI version 1.0
usb3: companion controllers, 2 ports each: usb0 usb1 usb2
usb3: <VIA VT6202 USB 2.0 controller> on ehci0
usb3: USB revision 2.0
uhub3: VIA EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
isab0: <PCI-ISA bridge> at device 17.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 8235 UDMA133 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xe400-0xe40f at device 17.1 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
rl0: <RealTek 8139 10/100BaseTX> port 0xe800-0xe8ff mem
0xe2002000-0xe20020ff irq 10 at device 19.0 on pci0
miibus1: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus1
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: Ethernet address: 00:20:ed:b5:a4:cf
speaker0: <PC speaker> port 0x61 on acpi0
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on
acpi0
sio0: type 16550A
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> flags 0x1000 irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model GlidePoint, device ID 0
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xcb7ff,0xcc000-0xd3fff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 1800073232 Hz quality 800
Timecounters tick every 1.000 msec
Fast IPsec: Initialized Security Association Processing.
ad0: 76319MB <Seagate ST380023A 3.30> at ata0-master UDMA100
acd0: DMA limited to UDMA33, device found non-ATA66 cable
acd0: DVDR <LITE-ON DVDRW SHW-1635S/YS0Q> at ata1-master UDMA33
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00
GEOM_LABEL: Label for provider acd0 is iso9660/pfSense.
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00
acd0: FAILURE - READ_BIG ILLEGAL REQUEST asc=0x64 ascq=0x00
Trying to mount root from cd9660:/dev/iso9660/pfSense
md0.uzip: 2328 x 65536 blocks
vr0: link state changed to UP
rl0: link state changed to UP
pflog0: promiscuous mode enabled

Besten Dank,
Timm

To Unsubscribe: send mail to majordomo(at)de.FreeBSD.org
with "unsubscribe de-bsd-questions" in the body of the message
Received on Tue 04 Nov 2008 - 16:33:50 CET

search this site