© 1995-2013 by The FreeBSD Project. All rights reserved.URL: http://lists.de.freebsd.org
Hi Bernd,
> Was sagt boot -v?
Ich habe mal den gesamten Kerneloutput mitgeschickt vielleicht könnte ihr damit
mehr anfangen als ich.
-----------------BOOT-------------------------------------------
Copyright (c) 1992-2000 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.1-RELEASE #1: Mon Sep 18 14:11:17 CEST 2000
root@:/usr/src/sys/compile/BERGLING
Calibrating clock(s) ... TSC clock: 348498076 Hz, i8254 clock: 1193225 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz
CLK_USE_TSC_CALIBRATION not specified - using old calibration method
Timecounter "TSC" frequency 348487381 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (348.49-MHz 686-class CPU)
Origin = "GenuineIntel" Id = 0x651 Stepping = 1
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR>
real memory = 134217728 (131072K bytes)
Physical memory chunk(s):
0x00001000 - 0x0009efff, 647168 bytes (158 pages)
0x002ee000 - 0x040fcfff, 65073152 bytes (15887 pages)
0x04100000 - 0x07ff7fff, 66027520 bytes (16120 pages)
avail memory = 127672320 (124680K bytes)
bios32: Found BIOS32 Service Directory header at 0xc00f6b40
bios32: Entry = 0xfd7a0 (c00fd7a0) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0x203
pnpbios: Found PnP BIOS data at 0xc00f6b90
pnpbios: Entry = f0000:9f56 Rev = 1.0
Other BIOS signatures found:
ACPI: 000f6b70
Preloaded elf kernel "kernel" at 0xc02d5000.
VESA: information block
56 45 53 41 00 02 00 01 00 01 00 00 00 00 22 00
00 01 80 00 00 01 0b 01 00 01 21 01 00 01 2a 01
00 01 00 01 01 01 10 01 11 01 12 01 03 01 13 01
14 01 15 01 05 01 16 01 17 01 18 01 07 01 19 01
VESA: 3 mode(s) found
VESA: v2.0, 8192k memory, flags:0x0, mode table:0xc0283342 (1000022)
VESA: ATI MACH64
VESA: ATI Technologies Inc. MACH64GT 01.00
Pentium Pro MTRR support enabled
md0: Malloc disk
Creating DISK md0
pci_open(1): mode 1 addr port (0x0cf8) is 0x80003904
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71908086)
npx0: <math processor> on motherboard
npx0: INT 16 interface
pci_open(1): mode 1 addr port (0x0cf8) is 0x00000000
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71908086)
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
found-> vendor=0x8086, dev=0x7190, revid=0x02
class=06-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base f8000000, size 26
found-> vendor=0x8086, dev=0x7191, revid=0x02
class=06-04-00, hdrtype=0x01, mfdev=0
subordinatebus=1 secondarybus=1
found-> vendor=0x8086, dev=0x7110, revid=0x02
class=06-01-00, hdrtype=0x00, mfdev=1
subordinatebus=0 secondarybus=0
found-> vendor=0x8086, dev=0x7111, revid=0x01
class=01-01-80, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[20]: type 1, range 32, base 00001000, size 4
found-> vendor=0x8086, dev=0x7112, revid=0x01
class=0c-03-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=d, irq=9
map[20]: type 1, range 32, base 00001020, size 5
found-> vendor=0x8086, dev=0x7113, revid=0x02
class=06-80-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[90]: type 1, range 32, base 00007000, size 4
found-> vendor=0x1013, dev=0x6001, revid=0x01
class=04-01-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=11
found-> vendor=0x11de, dev=0x6120, revid=0x02
class=04-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=10
found-> vendor=0x10b7, dev=0x9055, revid=0x30
class=02-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
intpin=a, irq=9
pci0: <PCI bus> on pcib0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
found-> vendor=0x1002, dev=0x4742, revid=0x5c
class=03-00-00, hdrtype=0x00, mfdev=0
subordinatebus=0 secondarybus=0
map[10]: type 1, range 32, base f5000000, size 24
map[14]: type 1, range 32, base 00009000, size 8
map[18]: type 1, range 32, base f4200000, size 12
pci1: <PCI bus> on pcib1
pci1: <ATI Mach64-GB graphics accelerator> (vendor=0x1002, dev=0x4742) at 0.0
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0x1000-0x100f at device 7.1 on pci0
ata0: iobase=0x01f0 altiobase=0x03f6 bmaddr=0x1000
ata0: mask=03 status0=50 status1=00
ata0: mask=03 status0=50 status1=00
ata0: devices = 0x1
ata0: at 0x1f0 irq 14 on atapci0
ata1: iobase=0x0170 altiobase=0x0376 bmaddr=0x1008
ata1: mask=01 status0=50 status1=ff
ata1: mask=01 status0=00 status1=ff
ata1: devices = 0x4
ata1: at 0x170 irq 15 on atapci0
pci0: <Intel 82371AB/EB (PIIX4) USB controller> (vendor=0x8086, dev=0x7112) at 7.2
irq 9
intpm0: <Intel 82371AB Power management controller> port 0x7000-0x700f irq 9 at
device 7.3 on pci0
intpm0: I/O mapped 7000
intpm0: intr IRQ 9 enabled revision 0
smbus0: <System Management Bus> on intsmb0
smb0: <SMBus general purpose I/O> on smbus0
intpm0: PM I/O mapped 8000
csa0: <Crystal Semiconductor CS4610/4611 Audio accelerator> irq 11 at device 11.0
on pci0
device_probe_and_attach: csa0 attach returned 6
pci0: <unknown card> (vendor=0x11de, dev=0x6120) at 14.0 irq 10
xl0: <3Com 3c905B-TX Fast Etherlink XL> irq 9 at device 16.0 on pci0
xl0: couldn't map ports/memory
device_probe_and_attach: xl0 attach returned 6
Trying Read_Port at 203
CSC0000: start dependant
CSC0000: adding dma mask 0x2
CSC0000: adding dma mask 0x9
CSC0000: adding irq mask 0x20
CSC0000: adding io range 0x534-0x537, size=0x4, align=0x4
CSC0000: adding io range 0x388-0x38b, size=0x4, align=0x8
CSC0000: adding io range 0x220-0x22f, size=0x10, align=0x20
CSC0000: start dependant
CSC0000: adding dma mask 0xa
CSC0000: adding dma mask 0xb
CSC0000: adding irq mask 0xcb8
CSC0000: adding io range 0x534-0xfff, size=0x4, align=0x4
CSC0000: adding io range 0x388-0x38b, size=0x4, align=0x8
CSC0000: adding io range 0x220-0x26f, size=0x10, align=0x20
CSC0000: start dependant
CSC0000: adding dma mask 0xb
CSC0000: adding irq mask 0xcb8
CSC0000: adding io range 0x534-0xfff, size=0x4, align=0x4
CSC0000: adding io range 0x388-0x3cb, size=0x4, align=0x8
CSC0000: adding io range 0x220-0x30f, size=0x10, align=0x20
CSC0000: end dependant
CSC0001: start dependant
CSC0001: adding io range 0x200-0x207, size=0x8, align=0x8
CSC0001: start dependant
CSC0001: adding io range 0x208-0x20f, size=0x8, align=0x8
CSC0001: end dependant
CSC0010: adding io range 0x120-0x3af, size=0x8, align=0x8
CSC0003: start dependant
CSC0003: adding irq mask 0x400
CSC0003: adding io range 0x330-0x331, size=0x2, align=0x8
CSC0003: start dependant
CSC0003: adding irq mask 0xcb8
CSC0003: adding io range 0x330-0x361, size=0x2, align=0x8
CSC0003: start dependant
CSC0003: adding io range 0x330-0x3e1, size=0x2, align=0x8
CSC0003: end dependant
ata-: ata0 exists, using next available unit number
ata-: ata1 exists, using next available unit number
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0047
atkbd: keyboard ID 0x41ab (2)
kbdc: RESET_KBD return code:00fa
kbdc: RESET_KBD status:00aa
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
psm0: current command byte:0047
kbdc: TEST_AUX_PORT status:00fa
psm0: strange result for test aux port (250).
kbdc: RESET_AUX return code:00fa
kbdc: RESET_AUX status:00aa
kbdc: RESET_AUX ID:0000
psm: status 00 02 64
psm: status 90 03 3c
psm: status 90 03 3c
psm: status 90 03 3c
psm: data 08 00 00
psm: status 00 00 28
psm: status 00 02 64
psm: data 08 00 00
psm: status 00 02 64
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model Generic PS/2 mouse, device ID 0-00, 3 buttons
psm0: config:00000000, flags:00000000, packet size:3
psm0: syncmask:c0, syncbits:00
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x700ff
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 06 e0 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x200>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: irq maps: 0x41 0x41 0x41 0x41
sio0: probe failed test(s): 0 1 2 4 6 7 9
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: irq maps: 0x41 0x41 0x41 0x41
sio1: probe failed test(s): 0 1 2 4 6 7 9
sio2: not probed (disabled)
sio3: not probed (disabled)
ppc0: parallel port not found.
isa_probe_children: probing PnP devices
pcm0: <CS423x> at port 0x534-0x537,0x388-0x38b,0x220-0x22f irq 5 drq 1,0 on isa0
pcm: setmap 30000, ff00; 0xc787b000 -> 30000
pcm: setmap 40000, ff00; 0xc788b000 -> 40000
unknown0: <Game> at port 0x200-0x207 on isa0
unknown1: <Ctrl> at port 0x120-0x127 on isa0
unknown2: <MPU> at port 0x330-0x331 irq 10 on isa0
BIOS Geometries:
0:030efe3f 0..782=783 cylinders, 0..254=255 heads, 1..63=63 sectors
0 accounted for
Device configuration finished.
bpf: lo0 attached
ata0-master: success setting up UDMA2 mode on PIIX4 chip
ad0: <WDC AC36400L/14.10R12> ATA-4 disk at ata0 as master
ad0: 6149MB (12594960 sectors), 13328 cyls, 15 heads, 63 S/T, 512 B/S
ad0: 16 secs/int, 1 depth queue, UDMA33
ad0: piomode=4 dmamode=2 udmamode=2 cblid=0
Creating DISK ad0
Creating DISK wd0
ata1-master: piomode=4 dmamode=2 udmamode=2 dmaflag=1
ata1-master: success setting up PIO4 mode on generic chip
acd0: <NEC CD-ROM DRIVE:28C/3.02> CDROM drive at ata1 as master
acd0: read 2412KB/s (5512KB/s), 128KB buffer, PIO4
acd0: Reads: CD-R, CD-RW, CD-DA
acd0: Audio: play, 256 volume levels
acd0: Mechanism: ejectable tray
acd0: Medium: no/blank disc inside, unlocked
Mounting root from ufs:/dev/ad0s2a
ad0s1: type 0x7, start 63, end = 8385929, size 8385867 : OK
ad0s2: type 0xa5, start 8385930, end = 12594959, size 4209030 : OK
start_init: trying /sbin/init
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x1020-0x103f irq 9 at device
7.2 on pci0
using shared irq9.
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub0: port 1 power on failed, IOERROR
uhub0: port 2 power on failed, IOERROR
csa0: <Crystal Semiconductor CS4610/4611 Audio accelerator> irq 11 at device 11.0
on pci0
device_probe_and_attach: csa0 attach returned 6
xl0: <3Com 3c905B-TX Fast Etherlink XL> irq 9 at device 16.0 on pci0
xl0: couldn't map ports/memory
device_probe_and_attach: xl0 attach returned 6
csa0: <Crystal Semiconductor CS4610/4611 Audio accelerator> irq 11 at device 11.0
on pci0
device_probe_and_attach: csa0 attach returned 6
xl0: <3Com 3c905B-TX Fast Etherlink XL> irq 9 at device 16.0 on pci0
xl0: couldn't map ports/memory
device_probe_and_attach: xl0 attach returned 6
Linux-ELF exec handler installed
splash: image decoder found: fade_saver
------------------------------BOOT---------------------------------------
>
> Kannst du mal zum Vergleich die boot disketten von einer aktuellen current
> snapshot (ftp://current.freebsd.org) einwerfen?
Habe ich gerade gemacht. Damit erkennt er die Karte ohne jegliche Fehlermeldung.
Kann ich diese Kernelversion vielleicht irgendwie nutzbar machen unter 4.1-RELEASE?
mfg
Gordon
To Unsubscribe: send mail to majordomo(at)de.FreeBSD.org
with "unsubscribe de-bsd-questions" in the body of the message
Received on Wed 20 Sep 2000 - 09:40:39 CEST