#####
aus dmesg.boot:

rl0: <RealTek 8139 10/100BaseTX> port 0x6100-0x61ff mem 0xe2004000-0xe20040ff
irq 18 at device 16.0 on pci0 rl0: Ethernet address: 00:e0:7d:7d:99:6f
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: supplying EUI64: 00:e0:7d:ff:fe:7d:99:6f                                                           
ed0 at port 0x320-0x33f iomem 0xd8000 irq 10 drq 0 on isa0
ed0: address 00:00:b4:83:3d:fd, type NE2000 (16 bit)                       
rl0: starting DAD for fe80:0001::02e0:7dff:fe7d:996f
ed0: starting DAD for fe80:0003::0200:b4ff:fe83:3dfd
ed0: DAD complete for fe80:0003::0200:b4ff:fe83:3dfd - no duplicates found
rl0: DAD complete for fe80:0001::02e0:7dff:fe7d:996f - no duplicates found            

#####
2xp200mmx# ifconfig -a
rl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
        inet 192.168.0.9 netmask 0xffffff00 broadcast 192.168.0.255
        inet6 fe80::2e0:7dff:fe7d:996f%rl0 prefixlen 64 scopeid 0x1
        ether 00:e0:7d:7d:99:6f
        media: autoselect (none) status: no carrier
        supported media: autoselect 100baseTX <full-duplex> 100baseTX 10baseT/UTP <full-duplex> 10baseT/UTP 100baseTX <hw-loopback>
lp0: flags=8810<POINTOPOINT,SIMPLEX,MULTICAST> mtu 1500
ed0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
        inet 192.168.0.3 netmask 0xffffff00 broadcast 192.168.0.255
        inet6 fe80::200:b4ff:fe83:3dfd%ed0 prefixlen 64 scopeid 0x3
        ether 00:00:b4:83:3d:fd
sl0: flags=c010<POINTOPOINT,LINK2,MULTICAST> mtu 552
ppp0: flags=8010<POINTOPOINT,MULTICAST> mtu 1500
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
        inet6 fe80::1%lo0 prefixlen 64 scopeid 0x6
        inet6 ::1 prefixlen 128
        inet 127.0.0.1 netmask 0xff000000
gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
        inet6 fe80::2e0:7dff:fe7d:996f%gif0 prefixlen 64 scopeid 0x7
gif1: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
        inet6 fe80::2e0:7dff:fe7d:996f%gif1 prefixlen 64 scopeid 0x8
gif2: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
        inet6 fe80::2e0:7dff:fe7d:996f%gif2 prefixlen 64 scopeid 0x9
gif3: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
        inet6 fe80::2e0:7dff:fe7d:996f%gif3 prefixlen 64 scopeid 0xa
stf0: flags=8000<MULTICAST> mtu 1280
        inet6 fe80::2e0:7dff:fe7d:996f%stf0 prefixlen 64 scopeid 0xb
faith0: flags=8000<MULTICAST> mtu 1500
2xp200mmx#   


#####
meine /etc/hosts:
127.0.0.1		localhost.BI localhost
192.168.0.3		2xp200mmx.BI 2xp200mmx
192.168.0.3		2xp200mmx.BI.
192.168.0.17		wingate
192.168.0.4		1xp133
192.168.0.2		2xp233mmx
192.168.0.9		2xp200mmx.BI 2xp200mmx
192.168.0.9		2xp200mmx.BI.